A pressure vessel has an internal volume of 0.5 m³ at atmospheric pressure (1.013 bar). It is desired to test the vessel at 300 bar by pumping water into it. The estimated variation in the change of the empty volume of the vessel due to pressurization to 300 bar is 6 percent. Assuming the bulk modulus of elasticity of water as 2 GPa, the mass of water to be pumped into the vessel to attain the desired

A pressure vessel has an internal volume of 0.5 m³ at atmospheric pressure (1.013 bar). It is desired to test the vessel at 300 bar by pumping water into it. The estimated variation in the change of the empty volume of the vessel due to pressurization to 300 bar is 6 percent. Assuming the bulk modulus of elasticity of water as 2 GPa, the mass of water to be pumped into the vessel to attain the desired

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

At a depth of 7 kilometers in the ocean, the pressure is 71.6 MPa. Assume the specific weight at the surface of 10.05 kN/m3 and an average bulk modulus of elasticity of 2.34 GPa for that pressure range. 19. Compute the change in specific volume between the surface and 7 km depth. a. –0.0000299 m³/kg b. -0.0000223 m³/kg c. -0.0000125 m³/kg d. -0.0000415 m³/kg 20. Specific weight at 7 kilometers below the ocean. с. 12.52 d. 19.52 а. 11.23 b. 10.37
Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the figure below. If viscous effects are negligible, (a) estimate the pressure needed to produce a 0.1-mm diameter water jet with a speed of 730 m/s. (b) determine the flowrate. (a) p = (b) Q = -0.1 mm Kbar cm³/sec
show step by step solution
If Surface tension for a Jet form is 0.05 N/mm and diameter of Jet is 0.3 Cm then pressure will be?
A steel pressure vessel (_y = 250 MPa, E = 200 GPa) has a length of 4 m and a diameter of 1.2 m (cylindrical). It is designed to hold natural gas at a pressure of 6 MPa. Calculate the wall thickness required to safely contain flammable gases, taking into account a safety factor of 5.0 to prevent failure. Use the "maximum principal stress" criterion. Next, calculate the Von Mises stress corresponding to the stress state of the reservoir. Enter your numerical answer. Please include free body diagrams and possible steps
3. What is the diameter change of a 50-ft spherical tank made of ½" steel plate due to internal pressure of 100 psi? Assume that the tank may be considered as "thin-walled" and that the steel remains elastic and has the properties Elastic modulus Poisson's ratio Internal pressure Thickness steel Diameter = = 11 30,000,000 psi 0.3 100 psi ½" 50 ft
A 0.6 m square glass plate slides on a plane with a slope of 30° from the horizontal (Figure 1.2). Knowing that the plate weighs 30 N and that it acquires a constant speed of 5 cm/s, it is asked: determine the dynamic viscosity of the film 0.1 mm lubricant, which is between the plates. Assume the velocity diagram linear in the fluid film). (R: 0.0833 Ns/m2) 5cm/s Figure 1.2 0.1 mm
A weight, with an unknown mass, falls through a distance of 10 millimeters (mm) onto a collar attached to the bottom end of a vertical bar. The bar is 3 meters (m) long and has a cross-sectional area of 600 square millimeters (mm2). The impact causes the bar to instantly stretch by 2 mm. The Young's modulus of the bar material is 200,000 MPa. Determine: 1. The weight of the falling object. 2. The stress experienced by the bar due to the impact.
Please answer fast
Please i need the answer as fast as you can
Glycerin flows at 35 m through a 150 mm diameter new wrought iron pipe at a velocity of 3 m/s. It has an absolute viscosity of 1.50 Pa-s and a specific gravity of glycerin = 1.26. 3. Solve for the coefficient of pipe friction.
The tank shown in the Figure below is fabricated from a 10-mm steel plate. If the internal pressure in the tank is 1.2 MPa, calculate the tangential stress in the tank in MPa? ... 400 mm 600 mm