At a depth of 7 kilometers in the ocean, the pressure is 71.6 MPa. Assume the specific weight at the surface of 10.05 kN/m3 and an average bulk modulus of elasticity of 2.34 GPa for that pressure range. 19. Compute the change in specific volume between the surface and 7 km depth. a. –0.0000299 m³/kg b. -0.0000223 m³/kg c. -0.0000125 m³/kg d. -0.0000415 m³/kg 20. Specific weight at 7 kilometers below the ocean. с. 12.52 d. 19.52 а. 11.23 b. 10.37

At a depth of 7 kilometers in the ocean, the pressure is 71.6 MPa. Assume the specific weight at the surface of 10.05 kN/m3 and an average bulk modulus of elasticity of 2.34 GPa for that pressure range. 19. Compute the change in specific volume between the surface and 7 km depth. a. –0.0000299 m³/kg b. -0.0000223 m³/kg c. -0.0000125 m³/kg d. -0.0000415 m³/kg 20. Specific weight at 7 kilometers below the ocean. с. 12.52 d. 19.52 а. 11.23 b. 10.37

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. The upward flow of water through a layer of sand in the tank shown in figure has the following properties: e =0.50, G-2.67. Determine the following: a) Effective stress at point A b) Effective stress at point B c) Upward seepage force per unit volume of soil 0.8m 3.5m Supply of Water 0.5m A B 1.9m
Strength of materials som.
redius af the tube (8) = 2 mm = 2X10m 3. Surface tensiom )= 0.752N/m wetting angle (0) = 130° To find the capillany Tse Tn te te be ch) =) Ytse In the tube h) =
3. Determine the bulk modulus of elasticity of a liquid, if the pressure of the liquid is increased from 7 MN/m² to 13 MN/m². The volume of liquid decreases by 0.15%. A.4 kN/m² B. 40 MN/m² C. 7.06 N/m² D. 4 GN/m²
Give me right solution
Solve.
2. Sand at a given relative density has a friction angle of approximately 33° (relatively low stress). When the sample is unsaturated at a given value of saturation (not given to you), the specimen has a negative pore pressure of 5 kPa. How tall a sandcastle "vertical" wall can you construct? What would happen to your sandcastle if the level of saturation suddenly increased? (Assume a total unit weight of 18 kN/m³)
A line load of q=60kn/m with alpha =300 is placed on a ground surface as shown in figure p4.1.Calculate the increase of pore water pressure at M immediately after application of the load for the cases given below. (a) z=10m ,X=0m ,v=0.5 ,A=0.45 (b) z=10m, X=2m,v=0.45, A=0.6
A circular tank applied a uniform pressure of 100 kPa on the ground surface. The diameter of the tank is 6 m, and the height is 10 m. What is the minimum depth in m below the centre of the tank such as the increase in vertical total stress does not exceed 10 kPa. (Acceptable tolerance = 5%).
Figure B: Stress diagram Total Stress (o) Pore Water Pressure (u) Effective Stress (o') 26.2 kPa 26.2 kPa -2.0 m 71.2 kPa 25 kPa i) ?? kPa -4-5 m -9.0 m i) ?? kPa 70 kPa 90.3 kPa Figure B Stress diagram By referring to the figure B, calculate the pore water pressure at depth 2m below the ground surface if the is a surcharge of 50 kPa at the ground surface. 50 kPa 0 kPa 10 kPa 100kPa
At a depth of 7km in the ocean the pressure is 957 MPA. Assume a specific weight at the surface of 13.9 kn/m^3 and an average bulk modulus of elasticity of 7.99 GPA for that pressure range. Compute the change in specific volume in mm^3/kg between the surface and 7km depth.
A cylindrical steel pressure vessel with a diameter of 1200 mm and a wall thickness of 20 mm is subjected to an internal pressure of 4.5 MPa. Determine the circumferential stress in the tank.