A pressure versus volume (pV) diagram for a system is shownin the figure. The arrows of the curve indicate the direction oftheprocess, and the points of interest are labeled. The valuesfor the points in the diagram are shown in the table.Volume (m³)Pressure (Pa)Vo = 25.8Po = 1.00 × 10ª%3D23Vị= 20.8Рі 3D 1.00 х 104V2 = 17.4P2 = 5.34 × 103V313.9P3 =5.34 x 1034V4 = 13.9P4 = 3.20 × 10³%3|Vs = 9.55P5 = 1.00 x 103%3DCalculate the amount of work done on the system from 0–2 (Wo2) and then for the entire curve from 0-5 (Wo5).Volume (m³)79.81 x103Wo2JIncorrect107.09 x103Wo5JIncorrectPressure (Pa)

Given: since, work done = area under PV curve

A pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values for the points in the diagram are shown in the table. Volume (m³) Pressure (Pa) Vo = 25.8 Po = 1.00 × 104 3 Vị = 20.8 Pi = 1.00 x 104 V2 = 17.4 P2 = 5.34 × 103 V3 = 13.9 P3 = 5.34 × 10³ 4 V4 = 13.9 P4 = 3.20 × 10³ Vs = 9.55 P5 = 1.00 × 103 Calculate the amount of work done on the system from 0–2 ( Wo2) and then for the entire curve from 0-5 (Wo5). Volume (m³) 79.81 x103 Wo2 = J Incorrect 107.09 ×103 Wos = J Incorrect Pressure (Pa)

A pressure versus volume (pV) diagram for a system is shown in the figure. The arrows of the curve indicate the direction of the process, and the points of interest are labeled. The values for the points in the diagram are shown in the table. Volume (m³) Pressure (Pa) Vo = 25.8 Po = 1.00 × 104 3 Vị = 20.8 Pi = 1.00 x 104 V2 = 17.4 P2 = 5.34 × 103 V3 = 13.9 P3 = 5.34 × 10³ 4 V4 = 13.9 P4 = 3.20 × 10³ Vs = 9.55 P5 = 1.00 × 103 Calculate the amount of work done on the system from 0–2 ( Wo2) and then for the entire curve from 0-5 (Wo5). Volume (m³) 79.81 x103 Wo2 = J Incorrect 107.09 ×103 Wos = J Incorrect Pressure (Pa)

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Membrane Servo-controlled Arm А В Patm Piston
0.0035 mol of gas undergoes the process shown in . (B) What is the initial temperature? (C) What is the final temperature?
45 J of work are done on the gas in the process shown in (Figure 1). Figure p (kPa) 300- K 200- 100- 2V₁ 3V₁ 0 0 V < 1 of 1 What is V₁ in cm³? Express your answer in cubic centimeters. ► View Available Hint(s) IVE ΑΣΦ V₁ = Submit Provide Feedback ? cm³
Make a PV graph using your data.
The heat engine shown in the figure uses 2.0 mol of a monatomic gas as the working substance. (Figure 1) Figure p (kPa) 600 400 200 0 0 0.025 0.050 V (m³) 1 of 1 Part A Determine T₁, T2, and T3. Enter your answers numerically separated by commas. Express your answer using two significant figures. T₁, T2, T3 = 600,1800,1200 K Submit Previous Answers Correct Part B
Answers (~1.9kJ, ~1.1kJ, ~4kJ) The figure to the right shows a gas contained in a vertical piston-cylinder assembly. A vertical shaft with a cross- sectional area of 1.0 cm² is attached to the top of the piston. The total mass of the piston and shaft is 35 kg. While the gas is slowly heated, the internal energy of the gas increases by 0.25 kJ, the potential energy of the piston-shaft combination increases by 0.5 kJ, and a force of 1300 N is exerted on the shaft as shown in the figure. The piston and cylinder are both good insulators and friction between them is negligible. The local atmospheric pressure is 1 bar and g = 9.81 m/s². Determine: 21 F-1300N (c) the heat transfer to the gas (kJ) (d) Provide a detailed accounting of where all of the heat energy has gone. C 19 4 A-14cm (a) the work done by the shaft (kJ) (b) the work done in displacing the atmosphere (kJ) (atmosphere does not act on shaft aka a donut area) D²10.0
A gas under constant pressure has a volume of 30.57m^3 and a temperature of 59.0 K. A change in temperature caused the volume to change to 121.14m^3. Based on the relationship between volume and temperature, what must have happened to the temperature? A- Temperature decreased B- Temperature increased C- Temperature stayed the same D- Temperature trend can not be determined
0.52 mol of argon gas is admitted to an evacuated 3.00 liter (3.00 × 10-3 m3) container at 20.0°C. The gas then undergoes an isobaric process to a temperature of 260°C. What is the final pressure of the gas, in atm? Your answer needs to have 3 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.