A power station is to supply four regions of louds whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station. |20,000 kW; 105-12×10 kWh|

A power station is to supply four regions of louds whose peak values are 10,000 kW, 5000 kW, 8000 kW and 7000 kW. The diversity factor of the load at the station is 1.5 and the average annual load factor is 60%. Calculate the maximum demand on the station and annual energy supplied from the station. |20,000 kW; 105-12×10 kWh|

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit shown, what is the complex power, S, consumed by the 18 + j32 N load impedance? (Assume the voltage source is in RMS.) 30 j8 N a 18 2 = 25 20° V j32 0 b 39.84/29.4° VA O 33.61Z27.7° VA O 11.24Z60.6° VA O 17.02Z – 64.0° VÀ
Q8 The average power to the plant shown in the figure is 2471 kW and the power factor is 0.707 lagging. The generator is sinusoidal in waveform with w = 377 4521 Volts. Determine the value of the ca- rad/sec and the effective value is pacitance C such that the power factor is 0.866 lagging. Plant Zoom
Q38 - Q40 refer to the table below: The voltage in a 60 Hz, 1-phase system has the following harmonic content: Harmonic Number Rms value 1 120 V 3 20V 5 9V Use this information to answer the questions Q25 to Q27. Q38. What is the rms value of the resulting current when this voltage is applied across a 100 resistive load? (a) 14.9 A (b) 12.2 A (c) 12.0 A (d) 3.9 A (e) 2.2 A Q39. What is the rms value of the resulting current when this voltage is applied across a 60 inductive load? (a) 24.83 A (b) 23.58 A (c) 20.33 A (d) 20.03 A (e) 20.00 A Q40. What is the rms value of the resulting current when this voltage is applied across a 69 capacitive load? (a) 24.83 A T (b) 23.58 A 20.99 A 20.36 A 20.00 A (c) (d) (e) 11
Problem 1 t Vsource (t) = 25 + 10 sin(377t) + 15 sin(754t) + 12 sin(1128t) Volts. The source voltage for the circuit in figure is of Determine: The average power at the load (Poc) The distortion factor (DF) 3) The source current total harmonic distortion (THD) Under what load condition(s) will the total harmonic distortion (THD) be zero? Consider the load using the is R2 R3 Vsource CI fundamental frequency only. Discuss. Sou 100n Figure I. Problem 1.
11-12 how to solve?!
In a 220 Vrms, 60 Hz. Source, determine the following values:
A power station has a maximum demand of 13590 kW. The annual load factor is 60% and plant capacity factor is 50%. Determine the reserve capacity of the plant.
A particular load has a pt of 0.78 lagging.The power delivered to the load is 36KW from a 240V rms 60Hz line. If 200μF capacitor is placed in parallel with the load, What is the new power factor of the total load. Select one: O a. 0.826 logging. O b. 0.5 leading. O c.0.94 logging O d. 0.7 leading.
92.54W A three phase full controlled converter is supplied by a phase voltage Vg=D120V, 60 Hz. Consider a resistive load R=10 Q. If the RMS value of the output current is equal to 10.94A and the input Volt Ampere VA = 3125VA, then the output power P. and the power factor would be equal to: Select one: O a. 1196.84W, 0.772 lagging O b. 3196.84W, 0.772 lagging Oc. 1196.84W, 0.382 lagging O d. 3196.84W, 0.382 lagging A transistor is used as a switch and the waveforms are shown below. The parameters are given as follows: Vcc = 200 V V -5 V Ie - 10 A Vera -2V L-- – 120 A t. -05us t - 1 us t. A us t. - 3us and f -10 TOSHIBA
An RLE load is operating from a type A chopper. If the supply voltage of 600 V, L 0.08 H, E = 120 V and R = 0 . For a duty cycle of 0.3, the chopping frequency to limit the amplitude of load current excursion to 10A is Hz.
i need the answer quickly
5- b) A factory has asynchronous motor loads with a power of 200 kW and a power factor of 0.8. When a synchronous motor with a power of 100 kW and a power factor of 0.909 is connected to this factory, what will be the new power factor of the system. Calculate the active and reactive power values in this case.