A power generating station has the following daily load cycle: Time (hrs) |0-6 6-10 10-12 12-16 16-20 20-24 Load 35 50 65 50 70 40 (MW) 2.1 Draw the load curve Determine: 2.2 the maximum demand, 2.3 unit generated per annum, 2.4 average load, and 2.5 load factor.

A power generating station has the following daily load cycle: Time (hrs) |0-6 6-10 10-12 12-16 16-20 20-24 Load 35 50 65 50 70 40 (MW) 2.1 Draw the load curve Determine: 2.2 the maximum demand, 2.3 unit generated per annum, 2.4 average load, and 2.5 load factor.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please solve what is ask with complete handwritten solution, Thank you so much!
The efficiency of wind turbine is equal to Moving 1000 J/s Wind 360 J/s Electrical 324 J/s air turbine generator NT = 40% b. а. NT = 90% NT = 32.4% d. C. NI = 36%
What is the total work in Kjoules of a conbined cyde power plant with a given plant efficency of 41 82 % and heat input of the system is equal to 122 BIU? 48.58 K joules B 51.28 K joules 58.45 K joules 62.85 K joules
Imagine that today is your first day on the job, and that from now on you will be the engineer responsible for a thermal machine. The machine operates according to the cycle below, functioning as a Rankine cycle. Figure 1. T-S diagram of the Rankine cycle. As a good engineer, you already know that, in order to know how a machine works, it is necessary to know its operating conditions. The boiler operates at a constant pressure equal to 8600 kPa and generates water vapor whose temperature is 400 °C. When passing through the turbine, the steam is expanded isetropically and enters the condenser as a two-phase mixture with a title equal to 0.80. The fluid is condensed at a constant pressure of 10 kPa, and then compressed isentropically, so that the fluid enters the boiler as a subcooled liquid. According to the information given above, determine: a) The change in internal energy (ΔU) and the change in entropy (ΔS) of the cycle. b) The net work recognized by the cycle (WNet). c) The thermal…
In the following figure, If Q=0.00594 m/s, what is the output power delivered by the 100% efficient motor. 14000 AP 12000 P 2000 AP O 34.66 HP PUMP MOTOR • None of them O 59400.00 HP O 43.52 HP O 79.62 HP O 108.79 HP Clear my choice
Fossil fuel power plant generates power to 5 residential household community with the following data: HS # 1 = 202 KW HS # 2 = 0.22 MW HS # 3 = 172 KW HS # 4 = 0.185 MW HS # 5 = 218 KW Diversity Factor = 80% Compute the maximum demand of the power plant in KW? A) 3,218.15 KW 2,012.50 KW 1,246.25 KW D 1,016.25
The figure below is the basic plot of pressure vs. volume for the Dual Standard Cycle. Constant pressure heat addition 3 4 PV = constant Нeat IN Adiabatic expansion Heat OUT (Constant volume heat rejection) Constant volume heat addition 1 Adiabatic compression Volume (V) Using the Dual Air Standard Cycle and the following data: • Assume constant properties of air. R= 287 J/kgK; Cp = 1005 J/kgK; Cv = 718 J/kgK; y = 1.4 Cycle compression ratio = 11 (v1/v2) Air conditions prior to compression: Pressure = 1.6 bar; Temperature = 298K Heat added at constant volume = 290000 J/kg %3D Heat added at constant pressure = 579000 J/kg Pressure (P) 2]
12- Post Tests and Homework's: Q1. Following data is given for a rope pulley transmitting 24 kW: Diameter of pulley = 400 mm; Speed = 110 r.p.m; Angle of groove 45°; Angle of lap = 160°; Coefficient of friction 0.28; Number of ropes = 10; Mass in kg / m length of ropes 53 C2. The working tension is limited to 122 C2; where C girth (i.e. circumference) of rope in metres. Find the initial tension and diameter of each rope. [Ans. 675.55 N; 31.57 mm] - = ELVEN = iversity
You have been tasked with the evaluation of alternate technologies for baseload power generation for a large urban center. The technologies to be considered are (1) coal fired power, (2) gas fired power, (3) nuclear power, (4) solar thermal power with storage, and (5) hydroelectric power. The criteria for assessment and relative weightings are presented below. Criterion Weighting (%) Capital Cost Generation Capacity Environmental Requirements and Impacts Social Acceptance Reliability 25 20 15 10 30 Review the literature for information relevant to each of the selection criteria for the technologies to be considered. Use a Kepner-Tregoe scorecard to determine the weighted scores for each technology option. Your scorecard should include a brief technical justification for the technology options against each criterion, together with references to the cited sources.
THA= 31 Celcius Degree TLA= 8 Celcius Degree QLA= 72 kW WA= 12 kW THB= 33 Celcius Degree TLB= 4 Celcius Degree QLB= 36 kW WB= 6 kW
11.) A heat engine with &=0.450 operates between two heat reservoirs at 300K and 700K. During each cycle of operation the engine takes in 200J of heat from the 700K reservoir. Th a) Find the magnitudes of the Wk, Qh, and Qc for one cycle of operation of the engine. b) Draw the energy flow diagram for one cycle of operation on a figure like the one shown to the right. Show an arrow and the value from part a) for: Wk, Qh, and Qc. c) Is this engine real, reversible, or impossible. Explain why. Engine Te
Q16) The following data are for a simple steam power plant as shown. State 2 3 4 7 P MPa 6.2 6.1 5.9 5.7 5.5 0,01 0,009 T°C 45 175 500 490 40 State 6 has x, = 0.92, and velocity of 200 m/s. The rate of steam flow is 25 kg/s, with 300 kW power input to the pump. Piping diameters are 200 mm from steam generator to the turbine and 75 mm from the condenser to the steam generator. Assume the cooling water comes from a lake at 15°C and is returned at 25°C. Determine: a) The rate of heat transfer in the condenser. b) The mass flow rate of cooling water from the lake. Steam Turbine generator c) The rate of heat transfer in the economizer, which is a low temperature heat exchanger. d) The rate of heat transfer needed in the steam generator. Cooling water Condenser e) Determine the velocity at state 5 and the power output of the turbine. Economizer Pump [a) -56130 kW, b) 1339.6 kg/s, c) 13750 kW, d) 67075 kW, e) 49 m/s, 24 800 kW]