What is the Carnot efficiency of a typical geothermal plant and its power capacity in MW? The average heat supply from the geothermal production well is around 1. 92 × 107 kW. The average ambient temperature and maximum temperature are 29 °C and 90 °C, respectively. power =

Q: A refrigeration plant that operates on the cycle shown below serves as a water chiller. Data on…

A:

Q: What type of CAD software could be used to test the medical scaffold made out of TPU that will be…

A: Given:What type of CAD software could be used to test the medical scaffold made out of TPU that will…

Q: INFORMATION ON SOLAR THERMAL SYSTEMS

A: Solar thermal power system is a system used to concentrate solar energy that is used to produce high…

Q: informations of thermal system

A: Thermal system s

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A:

Q: Epidemiological studies are all lutant concentrations. In all such studies there is the hazard that…

A: Air pollution is caused by solid and liquid particles, as well as some gases that are suspended…

Q: No gpt,solve in paper sheet. Free body diagram is must and should.

A: Approach to solving the question:Concept of Buoyancy The buoyant force on the hot air balloon must…

Q: I’m a doing a stiffness compliance matrix. E_1 is 150 GPA; what are the units of E_1 when I do…

A:

Q: Required information Three blocks A, B, and Cand a grooved block D have dimensions a, b, c, and das…

A: Calculated the mean gap and it's tolerance .

Q: What type of scale is 10:1? O Full Scale O Enlargement Scale O Reduction Scale

A:

Q: If FB = 560 N and Fc = 700 N, determine the magnitude and coordinate direction angles of the…

A:

Q: ##What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure…

A: hello Dear ):-Can update the question again . It is not show properly .thanks ):-Explanation:

Q: I need these 3 parts answered for a review activity.

A: Control frame has three compartments,Characteristic control compartment.Tolerance zone…

Q: The DP Transmitter device is used to measure level as an inferential measurement. When installing…

A: Differential pressure is calculated through the formula : Differential Pressure = Pressure High -…

Q: Don't use chatgpt will upvote

A: The voltmeter reading in the given circuit is relatively independent of the temperature of the…

Q: ment time data in the table, calcula Failure rate x 10- (h)

A: The name itself is well explained as, the mean or average time needed to repair mechanical or…

Q: I need help answering these 3 parts. 1. The size description of an object on the print can best be…

A: The size description of an object on the print can best be described as dimensioning.The correct…

Q: =5: A certain rocket engine has a temperature when in use of approximately 182°C. If left to cool in…

A:

Q: A new CNC machine is purchased for $40,000. The salvage value of the CNC machine is expected to be…

A: Solution: Given Data: P=$40000SV=15%P   To find: The book value of the CNC machine after 2 years of…

Q: What would an isometric of the oxygen piping system below look like, where PSA GEN = Pressure Swing…

A: can outline a general arrangement for the piping system:PSA GEN (Pressure Swing Adsorption Oxygen…

Q: If the cooling system operates above 100 degrees Celsius how should the cooling system, cooling…

A: The cooling system operates above 100 degrees Celsius how should the cooling system, cooling fans,…

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.