A porter governor have all arms 300 mm long. The upper arms are pivoted on the axis of rotation and the lower arms are attached to the sleeve at a distance of 35 mm from the axis. Each ball has a mass of 7 kg and load on sleeve is 54 kg. If the extreme radii of rotation of the balls are 200 mm and 250 mm. Determine the speed range of the governor and governor sensitivity.

A porter governor have all arms 300 mm long. The upper arms are pivoted on the axis of rotation and the lower arms are attached to the sleeve at a distance of 35 mm from the axis. Each ball has a mass of 7 kg and load on sleeve is 54 kg. If the extreme radii of rotation of the balls are 200 mm and 250 mm. Determine the speed range of the governor and governor sensitivity.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

With the assumption of no slipping, determine the mass m of the block which must be placed on the top of the cart (mc = 5.0 kg) in order that the system period be 0.58 s. What is the minimum coefficient of static friction for which the block will not slip relative to the cart if the cart is displaced 40 mm from the equilibrium position and released? Assume k = 740 N/m. -Hs m k mc
Consider the centrifugal clutch above that comprises of four ‘shoes’ symmetrically attached to the ‘spider’. Each shoe with its friction lining has a mass of 275 grams and is attached by means of a linear mechanical spring with a stiffness value of 7.5 kN/m. The coefficient of friction of the material attached to the shoes is 0.35. The centre of mass of each of the shoes is at a radius of 95 mm from the shaft centres in the rest position shown above and has a clearance distance of 9 mm to the outer drum. The outer drum has a wall thickness of 4 mm. Question 1 a. Determine the engagement speed of the centrifugal clutch. You should provide your answer in RPM (revolutions per minute) and rounded to the nearest whole value of RPM. b. Calculate the radial force acting on the clutch face when the driving shaft is rotating at a speed of 550 RPM. c. At the driving shaft speed of 550 RPM, what will be the value of torque transmitted to the driven shaft? Please note the equartions…
order that the sleeve may begin to lift at 300 rpin. If the stiffness of the spring is 30 kN m, what is the equilibrium speed corresponding to a sleeve lift of 10 mm. Q10A Porter governor has all four arms 200 min long. The upper arms are pivoted on the ass of rolation and the lower arms are attached to a sleeve at a distance of 25 mm from the axs Each ball has a mass of 2 kg and the mass of the load on the sleeve is 20 kg. If the radius of rolation of the balls at a speed of 228 rpm is 100 mm, find the speed of the governor after the sleeve has lifted 50 mm. Also determine the effort, power of the governor and governor sensitivity
Part A The arm is rotating at a rate of 0 = 4 rad/s when 6 = 3 rad/s and 0 = 180°. It is confined to move along the slotted path. Motion occurs in the horizontal plane. (Figure 1) Determine the force it must exert on the 0.25-kg smooth cylinder. Express your answer to three significant figures and include the appropriate units. ? F = Value Units Submit Request Answer Provide Feedback Figure <) 1 of 1 e = 4 rad/s, ö = 3 rad/s e = 180° ) m
The mass m in the given figure is attached to a rigid lever with negligible mass and negligible friction in the pivot. The input is the displacement x. When x and θ are zero, the springs are at their free length. Assuming that θ is small, identify the equation of motion for θ with x as the input.
The working fluid of the small engine vehicle uses a Porter governor of equalarms of 150 mm long to control its speed. The arms are pivoted on the axis ofrotation. The mass of each ball is 4 kg and the mass on the sleeve is 20 kg.5.1.The ball path is 100 mm when the governor begins to lift and 120 mm at themaximum speed. Calculate:Minimum speed of the governor.5.2.Maximum speed of the governor.5.3.Range of the speed.
The figure shows a schematic of a simple Watt governor mechanism with the spindle 0102 rotating at an angular velocity w about a vertical axis. The balls at P and S have equal mass. Assume that there is no friction anywhere and all other components are massless and rigid. The vertical distance between the horizontal plane of rotation of the balls and the pivot O₁ is denoted by h. The value of h = 400 mm at a certain w. If w is doubled, the value of h will be mm. (0) g = 9.8 m/s₂ h Spindle O Q Sleeve (QR) Cylindrical Joint R S
A box with mass m = 2.75 kg rests on the top of a table. The coefficient of static friction between the box and the table is μs = 0.71 and the coefficient of kinetic friction is μk = 0.34. Write an expression for Fm the minimum force required to produce movement of the box on the top of the table. Solve numerically for the magnitude of the force Fm in Newtons. Write an expression for a, the box's acceleration, after it begins moving. (Assume the minimum force, Fm, continues to be applied.) Solve numerically for the acceleration, a in m/s2.
The working fluid of the small engine vehicle uses a Porter governor of equal arms of 150 mm long to control it's speed. The arms are pivoted on the axis of rotation. The mass of each ball is 4 kg and the mass on the sleeve is 20 kg. The ball path is 100 mm when the governor begins to lift and 120 mm at the maximum speed. Calculate 5.1) Minimum speed of the governor 5.2)Maximum speed of the governor 5.3)Range of the speed
Consider the system shown at right. Find an equation of motion for the block with mass m,. Assume that the small wheel has negligible mass moment of inertia and that the larger one has a radius R and a mass moment of inertia I (measured respect to its axis of rotation). Note that there is a friction between the block with m2 mass m2 and the plane. The dynamic friction coefficient is equal to µa. m1 Md
A ball governor of the vertical compression spring type runs at a mean speed of N = 189.228 rev/min. The bell crank lever arms are a = 0.158 m and b = 0.063 m and the rotating balls have a mass of m = 2.793 kg each, and the ball radius is r = 0.114 m at the mean speed. Part A: If the speed range of the governor at the mean speed is A = 1.287 rev/min, determine the friction force Fu at the sleeve (neglect the effect of gravity on the balls). Part B: Determine the spring stiffness S that would be required to make the governor isochronous if the sleeve lift is y = 0.013 m from the mean position (assume the ball arm is vertical at the mean position).