A portable electric generator has a mass of 160kg with a mass centre at G as shown. Determine the reaction force under the wheel at O, when the upward force F which is applied at B just elevates support A of the ground 240 mm 325 135 mm mm If this reaction force can be written as R, = Rori + Rj, in kilo-newtons determine the components of the reaction force R and R %3D Roz Choose. Roy Choose. :

A portable electric generator has a mass of 160kg with a mass centre at G as shown. Determine the reaction force under the wheel at O, when the upward force F which is applied at B just elevates support A of the ground 240 mm 325 135 mm mm If this reaction force can be written as R, = Rori + Rj, in kilo-newtons determine the components of the reaction force R and R %3D Roz Choose. Roy Choose. :

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

6 in 60° 20 in Statics Instructor A vertical force of P = 100 lb is required to remove the nail at C from the board. Determine the magnitude of the moment about B exerted by the 100 lb vertical force. Draw a free body diagram for the system. Then, use what you know about moments to solve for Mp What is the magnitude of the moment at point B due to P if P = 100 lb and 9 = 10"? Round to the nearest whole number. Enter a response then click Submit below lb in
A sled with a mass of 25.0 kg rests on a horizontal sheet of essentially frictionless ice. It is attached by a 5.00-m rope to a post set in the ice. Once given a push, the sled revolves uniformly in a circle around the post as shown in the figure. If the sled makes five complete revolutions every minute, find the force F exerted on it by the cord. R-
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The total weight of the leg and the cast is W=250 N. The distance between the points A and B where the cables are attached to the leg is given as L=100 cm and the angle of the leg with the horizontal is γ=6°. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=40°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
1) Determine the force acting on the hydraulic cylinder BC. Express your answer in pounds to three significant figures. 2) Determine the horizontal and vertical components of reaction at the pin A(Ax,Ay). Express your answers in pounds to three significant figures separated by a comma.
2:56 90 0t O V all 22 classroom.google.com/u/ A ميكانيك هندسي Sgall LKs 23 A prybar is used to remove a nail as shown. De- termine the moment of the 240-N force about the peint O of contact between the prybar and the amall support block. 16m 240 N 16m aso mm PROBLEM 2/3s 2/ A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the wheelbarrow along with ita load of dirt in 185 Ib with center of gravity at G. For the configuration shown, what force must the man apply at A to make the net moment about the tie cuntact point B equal te ero? 30 mm PROBLEM 2/33 Representative Problems a34 An overhead view of a door is shown. If the com- pressive ferce aeting in the coupler arm of the hy draulic door elaser is 17 Ib with the arientation ahown, determine the moment of this force about the hinge axis 0. 20 PROBLEM 2/3s a7 A 150-N pull Tin applied to a cord, which is wound securely around the inner hub of the drum. Determine the moment of T about the drum center…
1) Determine the reaction at roller A. Express your answer to three significant figures and include the appropriate units. 2) Determine the horizontal and vertical components of reaction at pin B(Bx,By) . Express your answers in newtons to three significant figures separated by a comma.
Please help. Please make sure you clearly state how you got the numbers you got and why you are using them. Also please make sure you clearly put your formulas and label your units along the numbers that you are using. In the following frame ilustration, F1s 60 N and F2 is 9 N. What is the tension in the cable AB and the reaction force vector necessary to keep the system in static equilibrium? Give the X component reaction force at C( for an x axis going left to right). Also please solve for the rest of the 3 unknowns please. Thank you
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
Q1. As shown in the image below, the flower pot has a mass of 12 kg, and it is supported by cable AB and cable AC. Draw the free body diagram (FBD) of the ring at point A in order to determine the force in each supporting cable. Draw the FBD on paper and write in the answer space below "see netes". B 5 3. 从
Determine the reaction forces at the support A and the tension force T in the cable needed to support the 225 kg mass as shown in the figure below. Neglect the weight of the arm AB. 2.5 m |350 225 kg
Q2. Determine the stretch in each spring for equilibrium of the block of mass M. The springs are shown in the equilibrium position Given: M = 2 kg a - 3 m b = 3 m C - 4 m kAB - 30 kAC = 20 kAD - 40 g- 9.81 www D
Pivot A constant density bar with mass m and length Lis held in place as shown. Use the usual x,y,z coordinates for the following questions. Celling Cable 12. Measuring from the pivot, in the space below draw the torque-pic for the weight force exerted on the bar. Be sure your torque-pic includes both an expression for r in terms of L and also the value for the angle between r and weight force. Bar 350 Length = L