Answered: Determine the reaction forces at the…

Determine the reaction forces at the support A and the tension force T in the cable needed to support the 225 kg mass as shown in the figure below. Neglect the weight of the arm AB. 2.5 m 35 225 k

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.77P: The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B,...

See similar textbooks

Related questions

Q: Find the forces in the three members of the space truss shown in the figure. 600 mm 500 mm 820 mm-…

Q: The shear leg derrick is used to haul the 200-kg net of fish onto the dock. Determine the…

Q: A hot air balloon is held in place by three cables anchored to the ground at points B, C, and D. If…

A: Let FA be the lifting force of the balloon at 'A'. ⇒F⇀A=+FAk^ N Tension in cable, AD is given as:…

Q: 3. The homogeneous plate of weight 100kN is suspended from two cables. Determine the force that is…

Q: B D - W 2W - L/2 L/2 * L/2 L/2

Q: The mass center G of the 1540-kg rear-engine car is located as shown in the figure. Determine the…

Q: Determine the required mass (in kg) of the suspended cylinder then find the magnitude of the…

Q: The 53-kg cylinder is suspended from a clamping collar at C which can be positioned at any…

Q: etermine the torce in each cable needed fo support the flowerpot nose weight is 10ON

Q: Determine the tension in the cable at B, given that the uniform cylinder weighs 350 lb. Neglect…

A: Draw the free body diagram of the cylinder. OC=3 ftcos 40°OC=2.3 ft ED=3 ftsin 50°ED=2.3 ft

Q: The rectangular plate is suspended from verti- cal cables and is in equilibrium. The mass, m, of the…

Question

100%

Determine the reaction forces at the
support A and the tension force T in
the cable needed to support the 225 kg
mass as shown in the figure below.
Neglect the weight of the arm AB.
2.5 m
|350
225 kg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cable AOB weighs 5.2 N/m. When the horizontal 30-N force is applied to the roller support at B, the sag in the cable is 5 m. Find the span L of the cable.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The horizontal boom carries the weight W=108lb at A. The boom is supported by the cables AB and AC. The tensions in the cables are TAB=120lb and TAC=160lb. Determine the single force R that is equivalent to three forces acting on the boom at A.
Find the forces in the three members of the space truss shown in the figure. 600 mm 500 mm 820 mm- 550 mm 625 mm 950 N
The boom supports the two vertical loads. Neglect the size of the collars at D and B and the thickness of the boom, and compute the horizontal and vertical components of force at the pin A and the force in cable CB. Set F1 = 810 N and F2 = 320 N . Pt A. : Determine the horizontal and vertical components of force at the pin A Pt B: Determine the force in cable CB.
The L-shaped rod AOCD has an 80 kg mass hanging from it at B. The rod is leaning against a smooth wall at A. Point B is half way up OA. There is a journal bearing at C and a thrust bearing at D. They are properly aligned. A force F is pulling in the x-direction at B. Just as the rod comes off of the wall at A, what is the magnitude of the force F. 1 m B F 1m
ASAP, round off the final answer to 3 decimla places
Fishing line with a tensile strength of 25 lbs is used at B to fasten 2 members together as shown. Find the maximum force F that can be supported, given:L1 = 2 in, L2 = 4 in L3 = 6 in, L4 = 5 in
The system shown consists of three cables; 1, 2 and 3. Cable 1 passes through a frictionless pulley. A 6 kg mass is suspended. Determine the force in cable 3 considering the following data: y1 = 1.3 m, y2 = 1.1 m, y3 = 1.8 m, and x1 = 2.7 m.
The ramp of a ship has a weight of 107.6 Ib and a center of gravity at G. Determine the cable force in CD needed to just start lifting the ramp, (i.e., so the reaction at Bbecomes zero). Also, determine the horizontal and vertical components of force at the hinge (pin) at A. D 30 6 ft B Determine the vertical component of force at the hinge (pin) at A (in Ib).
1. The rectangular plate is suspended from verti- cal cables and is in equilibrium. The mass, m, of the plate and the dimension d are given. The weight of the plate acts through the center of the rectangle. What are the tensions T4, T; and Tc in each of the three cables? 1.5d B 2.5d 10.75d d H
1: When a force of 2 lb is applied to the handles of the brad squeezer, it pulls in the smooth rod AB. Determine the force P exerted on each of the smooth brads at C and D. (Note that P is not an external force applied to this system, it is shown in the figure to show you where force P is acting within the system (between the thin rods and the wood block.) 2 lb 0.25 in. -2 in- P E 1.5 in. 1 in.f 1.5 in. B D - 2 in.- 2 lb