A piston-cylinder assembly contains ammonia, initially at a temperature of -20°C and a quality of 50%. The ammonia is slowly heated to a final state where the pressure is 6 bar and the temperature is 120°C. While the ammonia is heated, its pressure varies linearly with specific volume. For the ammonia, determine the work and heat transfer, each in kJ/kg.

Q: 1. A 7-meter-long steel pipe was installed by a man during a cold whether at 20°C. What would be the…

A:

Q: 3. A long hollow cylinder has inner and outer radii R, and R2, respectively. The temperature of the…

A: Given details, For Hollow Cylinder of  Inner radius=R1 at Temperature T1 Outer radius=R2 at…

Q: Nitrogen gas has a heat capacity of 20.8 and 29.1 J/mol-C at constant volume and constant pressure…

A: Given Data: Specific heat capacity of N2 at constant Volume;Cv=20.8 J/mol °CSpecific heat capacity…

Q: 46. Air enters a diffuser with a velocity of 200m/s. Determine the speed of sound in m/s at the…

A: Given  Temperature (T) = 38 o C                              = 311.15 Velocity  = 200 m/s

Q: Write a process path for the heating and compressing of nitrogen. Include the state of the coumpound…

A: Given, Initial temperature, T1 = 293.15 K Initial pressure, P1 = 2×105 Pa Let the moles of the gas…

Q: The process of injecting water into a well under high pressure is called Thermal EOR a. False b.…

A: The oil is recovered from the reservoir by means of natural energy (pressure difference) but when…

Q: 4. Which property of a system increases when heat is transferred: (a) at constant volume, (b) at…

A:

Q: If the suction pressure of compressor equal to discharge pressure then the work of compression for…

A:

Q: How many heat are needed to change 50 kg of ice at -10.0 °C to steam at 250 °C?

A: Given: m  = 50 kg Ti = -10.0 °C (Ice) Tf = 250 °C (Steam)

Q: I understand that we have to use this formula Heat current=(k. Area. change in temperature)/length…

A: Firstly, the brass rod one end is in boiling water, which means this rod is hot. While the Copper…

Q: How much heat in kJ must be transferred to 10 kg of air to increase the temperature from 100C to…

A: From first law of thermodynamics, dU=dq-dw, Now dw=PdV, dU+PdV+VdP=dQ, As dP =0,

Q: A pipe (ID: 130 mm, OD: 165 mm, k=15 W/m²-K, Length: 2 meters)is insulated with several materials,…

A: Given Pipe Di=130mm D0=165mm K=15 W/(m2K) L=2m Inside fluid –Oil temperature T1=118℃ Insulation is…

Q: At a minimum reflux ratio, the boilup ratio is a) also at minimum b) at finite value c) equal to…

A:

Q: 16.5 Solve equation (16-19) for the temperature distribution in a plane wall if the internal heat…

A: Detailed answers show blown Explanation:

Q: Draw only the schematic diagram and T-S diagram.

A:

Q: Determine the external pressure if ethanol boils at 60 °C?

A: The boiling point of Ethanol at new pressure(P2)=60oC To Calculate the pressure(P2)=?

Q: How many heat are needed to change 50.0 grams of ice at -15.0 °C to steam at 120.0 °C?

A: Given: mass of ice = 50g=50g×kg1000g=0.05kg temperature of ice = -15°C=-15+273K=258K temperature of…

Q: DUE 9/2. Calculate the overall heat-transfer coefficient based on both inside and outside areas for…

A: Given : Inside heat transfer coefficient Outside heat transfer coefficientThermal conductivity of…

Q: A piston-cylinder device initially contains gas at 200 kPa. The system showed an expansion due to…

A:

Q: An automobile engine provides 596 Joules of work to push the pistons and generates 2246 Joules of…

A: Given that, Work done on the system W = 596 J Heat generated by the system Q = 2246 J It is required…

Q: If a heat pump works between-15°C and 50°C. Then, the coefficient of performance is... Select one:…

A:

Q: calculate applied pressure for expansion volume of inert nitrogen gas if the change of volume 20 cm³…

A:

Q: Which of the following is the rate of heat transfer unit 1. Watt 2. Pascal 3. Joule 4. None of these

A: Heat transfer is the transfer of heat due to modes of heat transfer like conduction, convection and…

Q: Which of the following is not an intensive

A: Intensive property is a thermodynamic property which does not depend on the amount of material in…

Q: Imagine gas in a piston – cylinder device. The fluid is compressed resulting to an increase in…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Find the volume of nitrogen gas when change heat at temperature 20 Co to 50 Coif that gas container…

A: Given data:  Initial temperature = 20 0C Final temperature = 50 0C

Q: In an engine working on an ideal otto cycle, the temperature at the beginning and end of the are…

A: Temperature at the beginning and end of the compression respectively 320C and 4240C.

Q: Question 4 A well-insulated piston contains ethylene. It is initially at 30 °C and 800 kPa with a…

A: Given Data  We need to find the following

Q: Determine the amount of heat needed to vaporize 26.7 g of water at 100C

A: Note: Since you have asked multiple questions, we will solve the first question for you. If you want…

Q: In an engine working on ideal Otto,.cycle, combustion takes place

A: The Otto Cycle involves four engine strokes. A stroke is defined as a process in which the…

Q: (2) Calculate the Fanning Friction Factor (f) using the formula: = 2.5 In Re, +1.75 8

A: Given, Equation for fanning friction factor is 1f = 2.5lnRef8+1.75    .....1   Here, Reynolds…

Q: A copper wire is stretched with a stress of 80 MPa at 20°C. If the length is held constant, to what…

A: Given data: Stress at 20 0C = 80 MPa αl for copper = 17×10-6 0C-1 Modulus of elasticity = 110 GPa

Q: Show that the friction heating in a hydraulic jump is given by 8(Z₂-Z₁)³ 42122 (7.67)

A: Friction heating in hydraulic systems occurs when fluid flows through pipes or channels,…

Q: 1. When a system absorbs heat, a part is stored within the system as the energy of internal motions…

A:

Q: Type of flow without heat transfer between the fluid and its external surroundings. O adiabatic W…

A: We have to select the correct answer for the flow without heat transfer between the fluid and its…