8A pipe of cross sectional area 2.34 m2 narrows whilesplitting into three pipes, each of cross-sectional area 0.8m². If the fluid is traveling at 2.1 m/s in the larger pipe,calculate the fluid speed in each of the narrower pipes.S/wi直0SNSYf5因 C/口f8F12E361OL}E3%24&7.6.Y

Answered: Image /qna-images/answer/c047c02b-e464-4b7b-b78d-fbeeacad7c82.jpg

A pipe of cross sectional area 2.34 m2 narrows while splitting into three pipes, each of cross-sectional area 0.8 m2. If the fluid is traveling at 2.1 m/s in the larger pipe, calculate the fluid speed in each of the narrower pipes. m/s

A pipe of cross sectional area 2.34 m2 narrows while splitting into three pipes, each of cross-sectional area 0.8 m2. If the fluid is traveling at 2.1 m/s in the larger pipe, calculate the fluid speed in each of the narrower pipes. m/s

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A round pipe of varying diameter carries petroleum from a wellhead to a refinery. At the wellhead, the pipe's diameter is 53.5 cm and the flow speed of the petroleum is 13.1 m/s. At the refinery, the petroleum flows at 5.25 m/s. What is the volume flow rate of the petroleum along the pipe, and what is the pipe's diameter at the refinery? volume flow rate: m³/s diameter: cm
Glycerin flows through a 6.0 cm diameter pipe at 0.98 m/s. What is the fluid’s speed in a 3.5 cm diameter pipe that connects with it, both pipes are flowing full.
A hydraulic piston has two surfaces which can move when a force is applied to them. On the left side, the piston surface is circular with a cross-sectional radius of 10 cm and on the right side it is square with a side of length 30 cm. A. If I push on the left side with 100 N of force, what total force will be exerted by the fluid in the piston on the right side? B. If I displace the piston on the left side by 18 cm, how far will the right surface move?
The figure illustrates flow through a pipe with diameters of 1 mm and 2 mm and with different elevations. px is the pressure in the pipe, and vx is the speed of a non-viscous incompressible fluid at locations x = Q,R,S,T, or U. T R D=1mm D= 2 mm Select the correct answers. Less than V PQ is PU. Less than V VT is ... 2vQ. Greater than Pu is ... PT. Submit Answer Incorrect. Tries 11/12 Previous Tries Post Discussion S Send Feedback
1.a) Water is moving through pipe with a cross sectional area of A1 = .8m^2 and a velocity of V1 = 6 m/s. The pipe constricts down to an area of A2 = .3 m^2. Calculate the water velocity V2 through the constriction A2. b.)
A large diameter closed top tank is filled with a depth of 3 meters of a fluid (density 1200 kg/m3). A small pipe leading from the bottom of the tank must carry the fluid some height above the fluid level in the tank. a) If a pressure of 2.5 Atmospheres is maintained in the space above the fill line in the tank how high above the fill line can the pipe carry the fluid and still provide an exit speed of 2 m/sec for the fluid out of the pipe? (the pressure at the exhaust end of the pipe is 1 atmosphere or about 1 x 105 pascal) If the pipe diameter is 2 cm, what will be the volume rate of flow (m3 /sec)
Water is flowing through a pipe with a constriction. The area of the narrow section is one-half the area of the wide section. If the velocity of the incompressible fluid is 3.2 m/s in the narrow section, then what is the velocity of the fluid in the wide section? Multiple Choice 0.9 m/s 1.0 m/s 1.6 m/s 1.8 m/s 1.9 m/s
Water travels through a pipe at 9.11 m/s. The pipe contracts from a crossectional area of 1.9 m2 to an area of 0.211 m2. a) What is the speed of the water in the second part of the pipe in m/s? m/s b) How much is the pressure change in KPa as the pipe contracts? The density of water is 1000 kg/m3. Enter a positive value for an increase in pressure, a negative value for a decrease. kPa
2. DETAILS S An incompressible fluid flows with velocity 12.00m through a round pipe with radius 2.30cm. If the pipe changes size and has a new, smaller radius of 0.20cm, what is the speed of the fluid moving through the narrower segment of pipe? m S What is the total volume flow rate for this pipe, in units of O 19.94- 11965698.10 L min L min L min 0.02- 1196.57- L min 1.20- L min L min MY NOTES (1000L=1m³ )? ASK YOUR TEACHER
4.0 mm 16. Consider the following diagram. (let air be an ideal, incompressible fluid) 2.0 cm 1200 cm'/s a. If the air is found to have a flow rate of 1200 cm3/s as it leaves the 4.00 mm diameter pipe, what is the velocity of the air in both segments of the pipe? b. If the density of air is 1.28 kg/m3 and the end of the pipe on the right opens up to the atmosphere, what is the pressure of the pipe at the 2.00 cm diameter section? C. If the fluid in the bottom of the U-tube is mercury with a density of 13,600 kg/m3 what is the difference between the surface levels of both sides of the tube, marked as h in the diagram?
An ideal incompressible fluid flows at 0.252 m/s through a 44-mm diameter cylindrical pipe. The pipe widens to a square cross sectional area that is 5.5 cm on a side. Assume steady flow throughout the system. a)What is the speed of the fluid through the square section of pipe? b)What is the flow rate in liters per minute?
A tank holds a large amount of water. A pipe is connected to the tank at the upper end and is open to the air at the lower end (see figure).The upper end of the pipe has a diameter of 17.0 cm. The lower end of the pipe has a diameter of 8.60 cm. The speed of the water at the upper end is 2.00 m/s.What is the flow rate of the water in the pipe?