A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.?. If the normal stress in bar (1) must be limited to 31 ksi, determine the maximum load P that may be applied to the rigid bar. 120 in. 80 in. (2) (1) B C

A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.?. If the normal stress in bar (1) must be limited to 31 ksi, determine the maximum load P that may be applied to the rigid bar. 120 in. 80 in. (2) (1) B C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A Rod AB consists of two cylindrical portions AC and BC, each with a cross-sectional area of 1750…

Q: A solid plastic rod has a diameter of d = 30 mm and a length of L = 625 mm. An axial load of P = 21…

A: Given: Diameter, d = 30 mm Length, L = 625 mm Axial load, P = 21 kN Elastic modulus, E = 2.4 GPa…

Q: 1.2 in. -2 in. A 1/8 in thick hollow polystyrene cylinder (E = 0.45 10^6 psi) and a rigid circular…

A: The elongation of rod AB: ∆LAB = 0.00562 inch.

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

Q: wo solid cylindrical rods support a load of P = 27 kN as shown. Rod 1 has a diameter of 16 mm and…

Q: Observe the figure that shows the assembly of the ACD arm, suspended by a bearing in C coupled to a…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: The hanger assembly shown is used to suspend equipment from the ceiling. The length of rod AB is LAB…

Q: Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P…

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick,…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: A steel cylinder is enclosed in a bronze sleeve; both simultaneously support a vertical compressive…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: w 12mm dia SK 18mm dia. P=12 kN HAD 12mm dia 2 m. 2. Three steel cable jointly support a load of…

Q: 2. The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A…

Q: 2.The rigid bar ABC shown in Fig.(1) is hinged at A and supported by a steel rod at B. Determine the…

Q: The cylindrical bar composed of two parts (AB and BC) is fixed at ends A and C. The two parts are…

Q: Three steel rods (E=200 GPa) support a 36-kN load P. Each of the rods AB and CD has a 200-mm²…

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and…

Q: A solid plastic rod has a diameter of d = 44 mm and a length of L = 700 mm. An axial load of P = 22…

Q: Rigid bar ABC is supported by bronze rods (1) and (2) as shown below. A concentrated load of P = 35…

A: Given:P=35kipsE=15000 ksiA=0.2 in2L1=11 ftL2=17 ftL3=9 fta=42 inb=78 in

Q: Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 1.625 in. wide and 1.125 in. thick,…

A: Given ,Rigid bar ABC is supported by pin connected bar 1.Width = 1.625 in.Thickness = 1.125…

Q: A rigid bar AN is hinged at A and is supported by a rod CD at C. The rod is pin connected at D.…

A: GivenE=200GPa

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied.
Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.25 in.?. If the normal stress in bar
(1) must be limited to 31 ksi, determine the maximum load P that may be applied to the rigid bar.
120 in.
80 in.
(2)
(1)
B
D
54 in.
54 in.
24 in.
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2 Please help. Provide Free Body Diagram, labeled with appropriate quantities to better understand. Also solve. Thank you.
A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal before the load P is applied. Bars (1) and (2) are both made from steel [E = 30,000 ksi] and both have a cross-sectional area of 1.5 in.2. Assume lengths of a = 44 in., b = 68 in., c = 28 in., L₁ = 50 in., and L₂= 100 in. The normal stress in bars (1) and (2) must be limited to 40 ksi. Determine the maximum load P that may be applied to the rigid bar. Answer in kips rounded-off to 2 decimal places. L₁ (1) Rigid bar b L₂ (2) D
just final answer A rigid component ABC is supported by a pin-connected member (1). The member has a rectangular cross-section with dimensions of 54 mm and 48 mm. The elasticity modulus of the material is 169 GPa. If L1=2421 mm, L2=1226 mm, L3=2272 mm, and L4=2072 mm; Determine the maximum normal stress (MPa) in member (1) without buckling.
An aluminium alloy rod of length 1.8m and rectangular cross-sectional of area 250mm^2 is subjected to a compressive load of 45kN. Young's modulus and Poisson's ratio for the material are: E = 71 GPa and v =0.33. Determine the decrease in length and increase in area of the bar.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F₁ = 13 kips, F₂ = 34 kips, and the normal stress in each rod must be limited to 22 ksi, determine the minimum diameter d₁ required for rod (1). A (2) d₁ F₂ B C O 1.087 in. O 0.823 in. O 0.541 in. O 0.867 in. O 1.003 in. d₂
PLEASE ANSWER NUMBER 8.MECH 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
Members BC and DE are 50 mm wide and 16 mm thick and made of steel (E = 200 GPa). Member AF is rigid. For a load of P = 60 kN, determine 500 mm (a) the normal stress in member BC, В C (b) the normal stress in member DE, 250 mm E (c) the displacement of point A. D Assume BC and DE do not yield or buckle. 250 mm F 500 mm- 650 mm
A 13-mm-diameter steel (E = 193 GPa) rod (2) is connected to a 27-mm-wide by 10-mm-thick rectangular aluminum (E = 72 GPa) bar (1), as shown. Assume L1 = 0.74 m and L2 = 1.38 m. Determine the force P (in kN rounded to the nearest tenths) required to stretch the assembly 8.1 mm.
A frame ABC consists of a horizontal beam BC which is supported by a round solid rod AB inclined at a 50° angle, as shown below. The ends of the rod AB are flattened to make pin connections at A and B. A vertical load of 5,000 N is acting at the mid-length of the beam. The rod material is a steel with modulus equal to 207 GPa and yield strength of 220 MPa. (a) Using a factor of safety of2.5, determine the diameter of the rod AB. (b) If a clevis joint is used at the pin connection at B, design the pin diameter so that it does not fail in shear. The tensile yield strength of the pin material is 300 MPa. Use a factor of safety between 1.5 and 2.5. 5,000 N В C 5 m 3 m 50° A