A pile of 0.50 m diameter and of length 10 m is embedded in a deposit of clay. The undrained strength parameters of the clay are cohesion 60 kN/m² and the angle in internal friction = 0. The skin friction capacity (kN) of the pile for an adhesion factor of 0.6, is

A pile of 0.50 m diameter and of length 10 m is embedded in a deposit of clay. The undrained strength parameters of the clay are cohesion 60 kN/m² and the angle in internal friction = 0. The skin friction capacity (kN) of the pile for an adhesion factor of 0.6, is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3.8 The soil profi le at a site for an offshore structure is shown in Figure P13.8. The height of…

A: Given:- The height of the pile above the sand surface = 15 m The diameter of the pile = 1.25 m The…

Q: A hammer pile driver has a hammer with mass of 700 kilograms. It falls onto the top of a…

Q: A 450 mm x 450 mm concrete pile 20.0 m long is driven into sand deposits with y = 17 kN/m³ and =…

Q: Figure shows a rectangular slab simply supported along all four edges which is isotropically…

A: Yield Moment = 30 km per meter width Size of rectangular slab = 8×6 m2

Q: A 50 cm diameter precast pile is driven by 9 m into a sandy soil. The standard penetration test…

A: D = 50 cm or 0.5 m L = 9 m Q = 4400 kNFS = 2.5

Q: The flow net around a sheet pile wall is shown in the sketch. The properties of the soil are…

Q: 1. Calculate the rate of flow or seepage flow per meter length of the sheet pile at right angle to…

A: Given data in question Permeability Elevation difference in upstream and downstream end. Number of…

Q: 11.26 Figure P11.26 shows a group pile in clay. Determine the consolidation settlement of the group.…

Q: A 20-metre-wide river flows over a rock pile as shown in the figure below. The rock pile generates…

A: In order to determine the direction of the flow. we will assume a direction. If the head loss coming…

Q: A pile of diameter 457 mm is fully embedded in a clay strata as shown in figure. C- 25 kN/m y= 16…

Q: The flow net around a sheet pile wall is shown in the

Q: 1.2X 10 cm/sec 1.0m 2.0 m 3.1X 10 cm/sec 4.3X 10 cm/sec 3.0m Figure 4

Q: Draw a flow net for the single row of sheet piles driven into a permeable layer as shown in Figure…

A: k = 4 x 10-4 cm/s or 4 x 10-6 m/sH1 = 3 m H2 = 0.5 m D = 1.5 m D1 = 3.75 m

Q: 2.10 Refer to Figure P 2.10 and use these values: H = 7 m, • H, = 1.75 m, D =7 m D = 3.5 m Draw a…

Q: The flow of water (mass density = 1000 kg/m³ and kinematic viscosity = 10-6 m²/s) in a commercial…

A: Given- Mass density- ρ=1000 kg/m3,kinematic viscosity-ν=10-6 m2/s,equivalent roughness ks=0.12 mm.

Q: shear strength of 80 kN/m². The lower la undrained shear strength of 120 kN/m². A n of pile doesn't…

A: solution (b) The top 1m of the pipe does not sopport load due to clay and concrete…

Q: For the one-dimensional consolidation test result shown .in Figure below, determine my

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: Design Procedure D y = 100 lb/ft³ ka = 0.3 kp = 3.0 Pp Z₁ Zp 4 2 Za Z Ap Solve for D Pa 1 2 3 4 0…

A: A cantilever retaining sheet pile is given and active and passive earth pressure is acting on it.

Q: Properties of soil Unconfined compression stress qu = 110 kpa Unit weight of soil Soil bearing…

A: The given data is as follows: Size of prestressed concrete pile=36 cmDesign capacity of pile=360…

Q: For the (4 x 4) pile group as shown in the figure, the settlement of pile group, in a normally…

Q: Q4: For the soil profile and loading condition shown in Figure (4). Find: a) Final consolidation…

A: Load, P = 2000 kN Coefficient of consolidation, Cv = 0.4 m2/yr Footing width, B = 2 m

Q: A square pile group of 9 piles passes through a recently filled up material of 3.5 m depth. The…

A: A square pile group of 9 piles,Depth of pile = 9 m,Depth of soil fill =3.5 m,Diameter of the pile=30…

Q: In-situ stresses – Seepage condition ground level sheet piling Example: For the sheet pile which T…

A: Consider the given data Yd=18 kN/m3Ysat=20 kN/m3Yw=10 kN/m2 Calculate total stress and effective…

Q: Q3) AYThe Figure below shows a long pile wall driven in sand with Coefficient of permeability K-…

A: Given that: ∆h = 1.2Coefficien of permeability, K = 0.05 cm/sec

Q: A group pile in clay is shown in the figure below. Determine the maximum vertical load Qg be applied…

A: Different soils strata and their properties are given. To find maximum permissible vertical load,…

Q: 11.22 A concrete pile measuring 0.406 m × 0.406 m in cross section is 18.3 m long. It is fully…

Q: Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here, L₁…

Q: A 600mm diameter pile is embedded in 3 layers of dense sand at a depth of 17m. Nq = 86. The…

A: Given, Nq = 86 D = 600 mm or 0.6 m

Q: A square pile of section 30 cm x 30 cm and length 10 m penetrates a deposit of clay having c = 5…

Q: n-situ stresses - Seepage condition xample: For the sheet pile which uried in sandy soil ,shown in…

A: The given data is: The water level is situated at the depth=2 m Assume, the dry unit weight of the…

Q: Determine the penetration depth for a 30 cm dia concrete pile which is required to carry a load of…

A: Given data: Try the embedded length as 14 m for the allowable load for a…

Q: A closed-end steel pipe pile is driven into thick saturated clay strata. The diameter and length of…

A: For closed-end steel pipeDiameter of pile: d = 0.4 mLength of Pile, L=32 mTo find

Q: 12.2 A 20 m long concrete pile is shown in Figure P12.2. Estimate the ultimate point load Q, by a.…

A: Required: Ultimate Point Load, Qp a. Meyerhof's Method b. Vesic's Method (m=600) c. Coyle and…

Q: A cellular cofferdam of 8.4 m radius and 15 m height is proposed for flood protection. Properties of…

A: The factor of Safety: The factor of safety is the ratio of the yield stress to the working stress of…

Concept explainers

Sediment transport

Sediment transport or Soil transport is the movement of solid particles, usually due to the combination of gravitational forces acting on the sediment, and the movement of the liquid at which the sediment enters. Soil erosion occurs in natural systems where the particles are sandstones (sand, rocks), mud, or clay; the liquid is air, water, or ice; and the gravitational force that works to move particles to the landing surface. Sediment transportation or soil migration due to the movement of liquids occurs in rivers, lakes, lakes, oceans, and other bodies of water as a result of currents and waves. Transportation is also caused by glaciers as they flow, and to places on earth under the influence of wind. Soil erosion due to gravity alone is possible in most sloping areas, including hills, scarves, cliffs, and the continental shelf — the continental boundary of the slope.

Question

A pile of 0.50 m diameter and of length 10 m is
embedded in a deposit of clay. The undrained
strength parameters of the clay are cohesion
60 kN/m² and the angle in internal friction = 0.
The skin friction capacity (kN) of the pile for an
adhesion factor of 0.6, is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A frictional pile with a circular cross-section (diameter = D) is pushed into the soil to a distance (L) and then it is subjected to an axial force (P) on its top end. Derive a formula to calculate the normal stress in any section x.
12.10 A concrete pile 15.24 m long having a cross section of 406 mm × 406 mm is fully embedded in a saturated clay layer for which Ysat = 19.02 kN/m³, p = 0, and c₂ = 76.7 kN/m². Determine the allowable load that the pile can carry. (Let FS = 3.) Use the a method Eq. (12.61) and Table 12.11 to estimate the skin friction and Vesic's method for point load estimation.
A 20-m-long concrete pile is shown in Figure P9.1. Estimate the ultimate point load Q, by a. Meyerhof's method b. Vesic's method c. Coyle and Castello's method Use m = 600 in Eq. (9.26). 9.1 Concrete pile 460 mm x 460 mm Loose sand di = 30° y = 18.6 kN/m3 20 m Dense sand d'2 = 42° y = 18.5 kN/m3 Figure P9.1
Q1/ For the footing shown in Figure (1), estimate the pile group capacity. 0.6m dia bored pile Clay c=80 kN/m² y-17kN/m² S=1.5 m T L=12 m
Solve using method of consistent deformation; EI =4x10^6 KN m^2, L=3.0, Wo=20KN/m
1. Refer the Fig. 1. Estimate the side resistance Qs by a. Meyerhof's method. K= 1.5 and d'= 0.6 Ø Coyle and Castello's method b. Concrete pile 460 mm x 450 mm I Loose sand 20 m 0', -30° Y=18.6 kN/m³ TE Dense sand 0₂-42* Y-18 6 kN/m² Fig. 1
A 7m high permanent sheet pile wall is to be constructed as part of a roadway project in a sandy soil. In this case, estimate the possible ground surface deformation. And determine the effected distance from the excavation due to this deformation.
[Geotechnical design] Please finish the answer step by step and clear to see. Thank you!
50. Whle drlling a well a rock layer Is encountered at 10000 ft. depth with an excess preSsure (overpressure) of 150 psl. An overpressure zone has fluld pressures In excess of the hydrostatic gradlent. If the overburden density Is 2400 kg/m* and the flutd column Is water what Is the effective stress at this depth? a. b. 57.68 MPa 4127.6psl d. 5549.0psl
A pile of diameter 250 mm is installed in a soil strata with a recently filled layer of clay of 3 m depth. The unit cohesion of the material is 18 kN/m² and unit weight of soil is 15 kN/m². The negative skin friction on the pile is equal to. (assume adhesion factor = 0.4)
Describe FOOTINGS ON OR NEAR SLOPES
11.10 A concrete pile 0.406 m x 0.406 m in cross section is shown in Figure P11.10. Calculate the ultimate skin friction resistance by using the a. a method b. A method c. ẞ method Use =20° for all clays, which are normally consolidated. 6.1 m 12.2 m 0.406 m Figure P11.10 Groundwater table Ysat Silty clay 18.55 kN/m³ Cu = 35 kN/m² Silty clay Ysat = 19.24 kN/m³ Cu = 75 kN/m²