A pile group of 9 piles placed in 3 row, 1 m apart between rows, with 1 m spacing 1 m in perpendicular direction between adjacent pile, carries a pointed load of 2000 KN with eccentricities of 400 mm and 200 mm with reference to the principal central directions. Find the maximum and minimum loads carried by respective candidate piles, and identify these piles on diagram. Also taking the column to be 500 mm x 500 mm. Determine the BM and SF at the column faces.

A pile group of 9 piles placed in 3 row, 1 m apart between rows, with 1 m spacing 1 m in perpendicular direction between adjacent pile, carries a pointed load of 2000 KN with eccentricities of 400 mm and 200 mm with reference to the principal central directions. Find the maximum and minimum loads carried by respective candidate piles, and identify these piles on diagram. Also taking the column to be 500 mm x 500 mm. Determine the BM and SF at the column faces.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: If your answer other than given options please leave it question.
Determine load carrying capacity of pile without considering critical depth concept. Diameter of pile 0.4 m.Ng =132 for o = 40° to m y 4.b Cot-opf "loose Sand K=1 = 21-15 From. 8a 19 Cu 20k Demse Sund 2 20 $=40° K=2 -I 30°
2. Two cylindrical steel piles (P1 and P2) are to be driven along the shore. Two total stations were set up at TS3 and TS4 respectively to guide pile driving of the two piles. TS1 and TS2 were observed from both instrument and the following data were recorded (refer from the figure below). The distances from both instrument to the pile locations were also measured. a. Determine the coordinates of TS3. b. Determine the coordinates of TS4. c. Determine the coordinates of P1 d. Determine the bearing from P1toP2. N=8415.591 E=3414.175 1975.655m ATS3 39°11'59", 1451 931m 3005.480m. 22 N=6523.709 1677.062m 54 2247.900m E=3021.832 2094.66 1m 45°20'18" 1994.379m 2702.590m
A concrete pile, 350 mm square, is driven into a thick deposit of medium sand with φ= 35° and ϒ = 19kn/m3. The water table lies at 2.0 m below ground level. Estimate the length of pile required to support a working load of 450 KN assuming a an overall factor of safety of 2.5. I will report and downvote wrong answer
A concrete pile is 15 m long and has 406 mm diameter circular cross section. The pile is fully embedded in sand, for which the unit weight '( = 18 kN/m3 and the frictional angle 8 = 30°. i) Calculate the ultimate point load Qp ii) Determine the total frictional resistance Qs iii) Determine the total ultimate load ofthe pile.
A group of 9 piles of 26 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.75 m. The length of the piles is 8 m. Unit cohesion of the clay is 93 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.65. Round off to two decimal places.
A concrete pile group 3x3 with spacing of 0.6m is used to support a wind turbine in a sand deposit. Individual pile diameter = 0.3 m and length=6m. A. If the allowable (working) lateral capacity for a single pile is 95 kN, what is the maximum allowable lateral deflection for each pile? B. Is the lateral deflection acceptable? Explain your answer in 1-2 sentences.
Q2: The plan of a group piles is shown below. Assume that the piles are embedded in a saturated homogeneous clay having a 7sa= 19.24 kN/m, C=41.2 kN/m? .Given: diameter of piles (D) = 305 mm, center-to-center spacing of piles 762 mm, and length of piles = 13.7 m. Find the allowable load-carrying capacity of the pile group. Use FS = 3. P
A group of 9 piles of 29 cm diameter is arranged in a square configuration with a center-to-center spacing of 1.01 m. The length of the piles is 12 m. Unit cohesion of the clay is 80 kPa. Determine the ultimate group capacity of the pile group based on block failure. Assume adhesion factor of 0.69.
A group of 16 piles of 50 cm diameter in arranged with a centry to centre sporing of 1.0 m. The piles are 9 m long and are embedded in soft stay with cohesion 30kN / (m^5) Bearing resistance may be neglected for the piles-Adhesion factor is 0.6. Determine the ulti mate Load capacity of the pile group.
Solve it asap plea
The section of a 3 x 4 group pile in a layered saturated clay is shown in the figure below. The piles are square in cross section (356 mm x 356 mm). The center-to-center spacing, d, of the piles is 889 mm. Determine the allowable load-bearing capacity of the pile group. Use FS = 4. Note that the groundwater table coincides with the ground surface.