A piece of metal was weighed on a laboratory balance five times and gave the following values: 15.75, 15.73, 15.77, 15.76 and 15.74 grams. Determine the average mass and standard deviation from the mean mass. (b) An object weighs 0.0930 grams on an analytical balance. Indicate the accuracy of the balance and the number of significant figures in this weight.

Q: An alloy that is made up of Brass and Chromium has specific gravity of 12. What is the mass of Brass…

A: The specific gravity of alloy is obtained from the density of alloy and density of water. The…

Q: The resulting soap has different characteristics. This depends on the ingredients used in making…

A: 1.To remove oil and dirt from clothes Soaps are the commonly used cleansing agents.  2. Soaps could…

Q: Does a solid have a vapor pressure?

A: The existence of vapor pressure for solid is to be mentioned.

Q: The density of gold is 19.3 g/cm^3 . A 6. 4 mg piece of gold is hammered into a square that is…

A: Part (a):The thickness of gold which is hammered into square is given in centimeters as: 8.6*10-6…

Q: Procedures: 1. Take 4, 500 ml of conical flasks, number them as 1,2,3,4. 2. Weigh 50g of sand to…

A: Leaching is the process of a solute becoming detached or extracted from its carrier substance by way…

Q: 5- 10% of 520 kg is equal to ( 56 kg , 54kg 52 kg. 50 kg ).

A: Given: M = 520 Kg X = 0.10  (10%)

Q: A pharmaceutical manufacturer forms tablets by compressing a granular material that contains the…

A: The Normal distribution curve equation can be written using mean and standard deviation as

Q: Define the term, “measurement uncertainty”. Among the instruments below above, which ones  have the…

A: Every matter in the universe is measured in some quantities and also has some units. Measurement is…

Q: Ipil-ipil leaves will be dried in a moving train of tray dryers. The wet leaves containing 75% water…

A: Initial mass% of water in leaves=75% Final mass% of water in leaves=15% Dimension of…

Q: 1. A chemical element has a unit cell BCC, the value of the edge is 295.6 pm (1 pm = 1x10^-12m) a)…

A: The value of edgea=295.6pm=295.6×10-12mTo find:a Atomic radius of the element.c Packing factor

Q: The weight of a mandarins Orange is about 6 ounces. A basket that weight 4 ounces will hold m…

A: Given that- Weight of mandarins one orange= 6 ounces Weight of basket = 4 ounces Total weight of…

Q: Spherical polymer beads are available in three different sizes, with diameters 0.1, 0.33 and 1 mm,…

A:

Q: The average deviation shows how precise a series of measurements are. Compare the preci- sion of the…

A: Data provided: Trial 25 mL graduated cylinder 100 mL graduated cylinder 1 16.8 mL 17.4 mL 2…

Q: A force of 20,000 N will cause a 1 cm×1 cm bar of magnesium to stretch from 10 cm to 10.045…

A: Given that :F = 20000 NArea = 1 cm x 1 cm = 1 cm2 d1  = 10 cm d2  = 10.045 cm

Q: It is estimated that 123,000 aluminumcans are recycled each minute. Assume that each canhas a mass…

A: Given Recycled Aluminium Can=123,000 per minute 1 Aluminium Can mass=14 g Find Total Aluminium Can…

Q: Estimate the:  a. Geometric mean b. Harmonic mean

A:

Q: A force 20, 000 N will cause a 1 cmx 1 cm bar of magnesium to stretch from 10 cm to 10.045 cm.…

A: f

Q: alculate the density of the salt solution.

A: Given that  diameter,d = 0.94 cm = 0.94 x 0.01m = 0.0094 m Height =1.24 cm  density of solid…

Q: Plain the reasons of the following: It is not recommended to use high rejection membranes for…

A: The high rejection membranes are recommended for the water with very high salinity like sea water.…

Q: Calculate the volume, in cubic meters, occupied by 40 kg of CO, ar standard conditions.

A: This problem is based on the standard conditions. The data given: Substance  = CO Mass of CO = 40 kg…

Q: A cylindrical specimen of a brass alloy 6.8 mm (0.27 in.) in diameter and 80.1 mm (3.16 in.) long is…

A: The stress and strain of engineering material are related to the stress-strain curve. The load is…

Q: 2. (a) A compound CuCl has face-centered cubic structure. Its density is 3.4 g cm. Calculate the…

A: Given CuCl has FCC structure ρ= 3.4 g/cm3  Find  Length of unit cell,a

Q: Transform the following graph into table values using the information given in the following graph.…

A: To find the points in a graph, select points in the graph and trace the corresponding values in…

Q: 49. A composite material is 57% resin (density of 2.3 g/cm³) and 43% unidirectionally placed carbon…

A: To find the density of the composite material, we can calculate the weighted average of the…

Q: A mixture of solid particles B & A having a size range of 5-9mm is to be separated by classification…

A:

Q: A tungsten chromium alloy contains 30% tungsten. The mass of the alloy is 10 kg. Determine the…

A: The total mass of the alloy, m = 10 kg.The mass fraction of tungsten in the alloy, y1 = 0.30The mass…

Q: Determine the flooding velocity and column diameter at the top tray of a valve-tray absorber using…

A:

Q: A sample mass is measured by ?using volumetric flask True Or False

A: Answer: False

Q: Explain what are the major raw materials used to produce propylene. For the most common raw…

A: Propylene is produced as a co-product of ethylene production thru the steam cracking (steam…

Q: 40 kg/h 0.900 kg A/kg 0.100 kg B/kg 30 kg/h 0.600 kg A/kg 0.400 kg B/kg 2. 100 kg/h 0.500 kg A/kg…

A:

Q: Bearings and other parts requiring exceptionally low friction and wear can be fabricated from an…

A:

Q: What is the mean particle size by number? b. What is the mean particle size by mass?

A: Given Size range <5 5-7 7-10 10-15 15-20 20-30 30-40 40-50 >50 No in range 0 50 150 200…

Q: Trex is a recycled plastic and wood particle product that can be used in place of lumber for decks.…

A: Size of the Trex deck board, V = 0.94 inches×5.5 inches×12 feet Thus, Volume of the Trex board, V =…

Q: Which one of the following statements is FALSE?

A: Analytical methods are the methods that used to determine physical, chemical properties of a sample.…

Units and Dimensions

Dimensions are the basic concepts of the measurement of quantities. Units are the means of expressing the dimensions. For instance, an area has a dimension of L2 and a unit of m2.