Aof magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gaugelength of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to:Load(KN)Al(mm)0.0 1.38 2.78 5.63 743 8.14 9,87 12.85 14,10 14.34 13.83 12,590.0 0.03 0.06 0.12 0.20 0.25 0.641.91 3,18 4.45 5.72 6.99a) Plot the data as engineering stress versus engineering strain.b) Compute the modulus of elasticity.Determine the tensile strength of this alloy.Sace

Given data: Cross-section of bar = A = 3.2 mm x 19.1 mm Gauge length = L = 63.5 mm For the given…

A of magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load (kN) (mm) a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity. e) Determine the tensile strength of this alloy. 0.0 1.38 2.78 5.63 743 8.14 9,87 12.85 14,10 14.34 13.83 12,59 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99

A of magnesium having a rectangular cross section of dimension 3.2 mm x 19.1 mm and a gauge length of 63.5 is pulled in tension. Use the load-elongation characteristics tabulated as follows to: Load (kN) (mm) a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity. e) Determine the tensile strength of this alloy. 0.0 1.38 2.78 5.63 743 8.14 9,87 12.85 14,10 14.34 13.83 12,59 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 6.99

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A tension test on an aluminum plate resulted in the following engineering stress-engineering strain data as reported in the first and second column of the table below (reduction of area, RA=17%): S (psi) e (in/in) σ (psi) ε (in/in) 10500 0.001 10510.5 0.000995 21000 0.002 31200 0.003 41300 0.004 51200 0.005 61200 0.006 70600 0.007 74700 0.0075 76800 0.008 77600 0.0085 78000 0.009 78400 0.0095 78700 0.01 81200 0.02 83000 0.03 84200 0.04 85400 0.05 86200 0.06 86800 0.07 *87200 0.08 **86200 0.1 Note: * maximum load, ** load at fracture a) Calculate the corresponding true stress and true strain and give your results in a table along with the engineering stress, engineering strain shown in the of table above (column 3 and 4). b) Plot the true stress-true strain curve on a rectangular coordinate. c) Plot the true stress-true strain curve on a log-log graph and determine the plastic flow curve parameters K and n, the yield strength, Y, and the elastic modulus, E of the material.
stress 0.02 0.018 0.016 0.014 0.012 0.01 0.008 0.006 0.004 0.002 0.05 0.1 0.15 0.2 0.25 0.3 0.35 Determine : 1- Stress, Stratn care 2. elastic Zone 3. yield sbresscoys 4- plastic Zone 5- UItimate Stress Cous 6- Elongation 7- propotionaL stress cops 8-fructurc stress coF)
I have plotted stress strain curve as shown in attached pictures. I want to know that: What does the slope represent and what does it indicate? Can you find what is the material used? How to find it?
Determine the tensile yield strength (0.2% offset) and the maximum strength of a metal alloy having the following tensile stress-strain diagram. Tensile stress-strain diagram 150 100 0.05 02 05 035 Strain 300 250 200 150 100 50 W Stress (Mpa)
I need the answer as soon as possible
Determine the young's modulus of metal alloy having the following tensile stress - strain diagram
A mild steel specimen of Diameter 9 mm, Length 11 cm is subjected to tensile load and it is found that the Strain-induced on the specimen is 18 x 10-3. Take the Modulus of elasticity as 201 x 103 MPa. Determine the following i) Tensile Load ii) Tensile Stress iii) Change in Length iv) Final cross-sectional area at failure if the percentage of reduction in area is 49 %.
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Figure σ (ksi) 0 33.2 45.5 49.4 51.5 53.4 € (in./in.) 0 0.0006 0.0010 0.0014 0.0018 0.0022 1 of 1 Part B Determine the modulus of elasticity. E = ksi Submit Part C Determine the modulus of resilience. Ur= in-lb in³ Submit Request Answer Provide Feedback Request Answer
3
n=0,10 F Strain Stress n=019 9) Give an example of: i) a truly elastic material:..... ...ii) a material which is not viscoelastic:.... 10) If you require fatigue resistance for an application, among all manufacturing methods (machining, forging rolling casting deen drawing hich wath
i need the answer quickly
A cylindrical specimen of 1018 steel having a diameter of 6.35 mm and a gauge length of38.1 mm is pulled in tension. Use the load-elongation characteristics tabulated below. Compute the modulus of elasticity and the approximate ductility, in percent elongation?