A- Obtain the transfer function Xo(s)/X ¡(s) of the mechanical system shown in Figure A(I). Also obtain the transfer function Eo(s)/E; (s) of the electrical system shown in Figure A(II). Show that these transfer functions of the two systems are of identical form and thus they are analogous systems. k₁ b₂ k₂ ww (1) b₁ Xi Xo y ei R₂ www C₂ (II) R₁ C₁ ww Co

A- Obtain the transfer function Xo(s)/X ¡(s) of the mechanical system shown in Figure A(I). Also obtain the transfer function Eo(s)/E; (s) of the electrical system shown in Figure A(II). Show that these transfer functions of the two systems are of identical form and thus they are analogous systems. k₁ b₂ k₂ ww (1) b₁ Xi Xo y ei R₂ www C₂ (II) R₁ C₁ ww Co

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

38% @ uO 11:52 4 لا توجد خدمة و Ch#2_Exercise#5.p... Ch#2 Active Filters Exercise#5 Find the transfer function T(s) for the circuit shown in figure below. CAI RAI Vin = CBI o Vo R2 Stay Home. Electricat Engineerng Department Unvensity of aurah HH
1.32 The feedback system shown in figure below is stable for all values of k given by k s(s + 1) (s + 6) (a) k > 0 (b) k < 0 (c) 0 < k < 42 (d) 0 < k < 60
Q: Determine the transfer function (S) = VO(S) / VI(S) , poles, zeroes, type and order of the circuit shown in the figure .below (theoretically and practically using MATLAB), then discuss your results. びカ R1 R2 つ Shows an electrical -circuit called ( Phase-lag network)
Find the output for the system represented by transfer function shown in figure (2-10) analytically and compare with the simulated result. (Assuming all initial conditions is zero)
Figure 1 Block diagram of the system in Question 1. a. Determine the transfer function between u and y. b. b. Determine the poles and the zeros of the system when the transfer functions are
K A certain analog plant function is shown in figure 2 and its transfer function G,(s) = (s+a)(s+b)· This plant is sampled using a zero-order hold (ZOH) before the signal is fed to a digital controller. Using 0.45 second as sampling time and K=14; a=3; b=5, Do the following. Zero-order Plant Plant Hold ZOH Gp(s) G(z) Figure 2 i. Obtain the z-transform G(z) ii. Discuss the importance of a ZOH in digital control systems
|| For the circuit shown in the figure below, assuming that VA = ∞, the input impedance is expressed by: Vcc O O Q₂ Rc Vino O Select one: Q₁ a. Vout 1/9m1 b. 1/9m1 + BRc 1/9m1 + Rc None of these O c. O d. V₂
Find all possible impulse response for the system transfer function given by
CLTF( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
Obtain the transfer function of the system and find the unit step response. Show all intermediate operations in detail. m=1 kg b=20 Ns/m k=125 N/m ww k m
Accept that the M=2 kg, K=1 N/m, fv=1 N-s/m and find the transfer function according to thosevalues
Signals and system