A note about rms, which stands for root-mean-square: The rms voltage is a measure of the average effective voltage. If you use peak (maximum) values of voltage or current in any of the transformer equations, you get peak values out. If you use rms values in the equations, you get rms values out. The bottom line: Don't be confused by the rms values-you can use them in the equations and you'll be fine. A typical pole-mounted transformer, the last step in the power distribution process before electricity is delivered to residential customers, has an rms voltage of 9600 volts on the primary coil. The secondary coil has an rms output voltage of 240 volts, which is delivered to one or more houses. (a) What is the ratio of the number of turns in the primary coil to the number in the secondary? N₂ X Ns (b) If the rms current on the primary side is 6.00 A, and each house requires an rms current of 40 A, how many houses can this transformer supply electricity to? houses

A note about rms, which stands for root-mean-square: The rms voltage is a measure of the average effective voltage. If you use peak (maximum) values of voltage or current in any of the transformer equations, you get peak values out. If you use rms values in the equations, you get rms values out. The bottom line: Don't be confused by the rms values-you can use them in the equations and you'll be fine. A typical pole-mounted transformer, the last step in the power distribution process before electricity is delivered to residential customers, has an rms voltage of 9600 volts on the primary coil. The secondary coil has an rms output voltage of 240 volts, which is delivered to one or more houses. (a) What is the ratio of the number of turns in the primary coil to the number in the secondary? N₂ X Ns (b) If the rms current on the primary side is 6.00 A, and each house requires an rms current of 40 A, how many houses can this transformer supply electricity to? houses

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A RLC series circuit has C=5×10^−3 [F],R=100 [Ω], andL=3×10^−3 [H]. This circuit is connected to an AC supply that gives out 10 [V] at 600 [Hz]. Which of the following statements is true regarding the current and the voltage of the generator? A. The source voltage and current are in phase. B. The source voltage lags the current. C. The source voltage leads the current. D. The current leads the source voltage.
Please box answers for D
Please make sure your answer is 100% correct, thanks A 69 Ω resistor, an 7.4 μF capacitor, and a 32 mH inductor are connected in series in an ac circuit. Part A. Calculate the impedance for a source frequency of 300 Hz. Express your answer with the appropriate units. Part B. Calculate the impedance for a source frequency of 30.0 kHz. Express your answer with the appropriate units.
An RC circuit has an impedance of 130 Ω when connected across a 60.0 Hz power source that produces a 90.0 Vrms voltage. The capacitor has a capacitance of 75.0 ?F. An inductor with inductance 130 mH is added, to make a series RLC circuit. Draw a clear physics diagram of the problem What is the impedance of the new RLC circuit? What is the maximum energy stored in the inductor in this circuit? If the frequency is increased slightly, will the phase angle increase or decrease? Explain qualitatively.
In a simple AC circuit shown on the right, C = 0.0045 F, L = 1.4 H, R = 45 Ω, and ΔV = ΔVmaxsin(ωt), where ΔVmax = 5.5 V and ω = 45 rad/s. a. Calculate the numerical value of Z in ohms. b. Calculate the numerical value of Imax in A. c. Calculate the numerical value of φ in radians.
An AC circuit has a purely capacitive load. If the amplitude of the EMF is 10.27 V with a frequency of 193.3 Hz, the capacitance is 73.2 UF, and the driving voltage is initially zero. What is the current in the capacitor after 0.732 s? A Save for Later Submit Answer
Suppose we have an ideal transformer connected to a V1 = 260 [V] AC source and is supplying V2 = 13 [V] on a device. What is the ratio between the current of the AC source I1 and the current across the device I2, I1:I2? A. 20:1 B. 1:1 C. 1:20 D. Not enough information
The frequency of oscillation of the LC circuit in the figure is 200 kHz. At time t=0 the upper capacitor plate has its maximum positive charge. Select True or False for all statements. 1. At t=1.25 us, the current is maximum. 2. At t=2.50 us, the charge on the lower plate has its maximum positive value. 3. At t=1.25 us, half the energy is stored in the capacitor, half in the inductor. 4. At t=5.00 us, the energy is completely stored in the capacitor. 5. At t=1.25 us, the charge on the lower plate has its maximum positive value. 6. At t=2.50 us, the current is zero.
The output voltage of an AC source is given by: & 170 sin(377t), where & is in volts and t in seconds. The source is connected across a series RL circuit, in which R = 200.0 2, L = 0.200 H. a. Determine the maximum voltage across the inductor. b. What average power is delivered to the circuit? c. What capacitor should be added to the circuit so that the power delivered is maximum? R L c. How long does it take the electron to make Found X
An RC circuit has an impedance of 130 Ω when connected across a 60.0 Hz power source that produces a 90.0 Vrms voltage. The capacitor has a capacitance of 75.0 μF. An inductor with inductance 130 mH is added, to make a series RLC circuit.a. Draw a clear physics diagram of the problem.b. What is the impedance of the new RLC circuit?c. What is the maximum energy stored in the inductor in this circuit?d. If the frequency is increased slightly, will the phase angle increase ordecrease?
Please don't provide handwritten solution....
A RLC series circuit has C = 5 x 10-³ [F], R = 100 [22], and L = 3 × 10-³ [H]. This circuit is connected to an AC supply that gives out 10 [V] at 600 [Hz]. Which of the following statements is true regarding the current and the voltage of the generator? A. The source voltage lags the current. B. The source voltage leads the current. C. The current leads the source voltage. D. The source voltage and current are in phase.