The output voltage of an AC source is given by: & 170 sin(377t), where & is in volts and t inseconds. The source is connected across a series RL circuit, in which R = 200.0 2,L = 0.200 H.a. Determine the maximum voltage across the inductor.b. What average power is delivered to the circuit?c. What capacitor should be added to the circuit so that the power delivered is maximum?RLc. How long does it take the electron to make Found X

Answered: Image /qna-images/answer/f718adc5-7ad8-4551-ba68-60692e66b0e0.jpg

Answered: The output voltage of an AC source is…

Similar questions

5. Suppose that a LRC series circuit like the one below has the following values for inductance, resistance, and capacitance: L = 1 h, R = 2, C = 0.25 f. Also suppose that the impressed voltage in the circuit is modeled by the function e(t): 50 cost V. = a. Write a differential equation that models this scenario and find a general solution for the charge q in the circuit at any time t. b. Is this system underdamped, critically damped, or overdamped? c. If the initial charge q(0) = 4 C and the initial current i(0) = 0 A find the solution given these initial conditions. Note: i(t) = q'(t). d. Use a graphing utility to sketch out the charge q(t) and current i(t). e. What are the steady-state solutions for charge and current?
The instantaneous power dissipated by a 20 Ω resistor connected to an AC source is shown.a. What is the rms voltage across the resistor?b. What is the peak current through the resistor?c. What is the frequency of the AC source?
11. The rms current in an RLC circuit depends on the frequency of the power source as shown below. It reaches its maximum value at f= 80 Hz. Find the rms voltage applied to the circuit if R = 10 22, C = 198 µF, and L = 20 mH. A. 25 V B. 50 V C. 75 V D. 100 V E. 125 V Current (Amps) 25 6 2.0 15 1.0 0.5 50 100 Frequency (Hertz) 150 200 250
11. The rms current in an RLC circuit depends on the frequency of the power source as shown below. It reaches its maximum value at f = 80 Hz. Find the rms voltage applied to the circuit if R = 102, C = 198 µF, and L = 20 mH. A. 25 V B. 50 V C. 75 V D. 100 V E. 125 V Current (Amps) 2.5 2.0 1.5 1.0 0.5 50 100 Frequency (Hertz) 150 200 250
A microscope illuminator uses a transformer to step down the 120 V AC of the wall outlet to power a 12.0 V, 50 W microscope bulb.a. What is the resistance of the bulb filament?b. What is the rms current in the bulb filament?c. What is the rms current in the primary coil?
A two-part problem concerning resonance in an RLC series circuit. a. Calculate the resonant angular frequency of an RLC series circuit for which R = 20 Ω, L = 75 mH, and C = 4.0 uF. b. Does the resonant angular frequency increase, decrease, or stay the same if the resistance is changed to 300 Ω? Does changing this resistance have any other effect on the circuit? Explain.
4. A 25.0 mH inductor, a 2.00 uF capacitor, and a certain resistor are connected in series across an ac voltage source at 1000 Hz. If the impedance of this circuit is 200 Ω, what is the value of the resistor?
15. A sinusoidal a.c. supply of frequency 200 Hz and peak voltage 24 V is applied to a pure capacitor is 4.4 uF, what is the rms value of the current in the circuit? A. 3.4 mA C. 67 mA B. 21 mA D. 94 mA 16. A capacitor is connected to an alternating voltage. The current in the circuit varies with time as shown in the graph. Current S Time
Q02
A capacitor is connected across the terminals of an ac generator that has a frequency of 490 Hz and supplies a voltage of 39 V. When a second capacitor is connected in parallel with the first one, the current from the generator increases by 0.18 A. Find the capacitance of the second capacitor. Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. Number 1 a pag Jadi Units
TC 5. A circuit connected to an ac generator has & = 31.4sin ( wt 4. --). With w = 350 rad/s. The 0.622 sin (wt -=).a) At what time does the generator reach maximum (ot current is given by I = %3D 4 emf for the first time? B) What time does it reach the max current c)If the circuit has only one element is that a capacitor inductor or resistor, explain d) Find the value of that element( Ans: a)6.7 ms b0 11.2 ms c) Inductor d) 144 mH ins prt sc delete f12 f10 A fs f6 17
26. At time r=0, the voltage across a 102 resistor connected to an AC voltage source v(t) = 6V cos(2r(50HZ)t) is 6V. What is the current through the resistor 0.1 seconds later? A. 0A %3D B. 0.1A C. 0.6A D. 1A E. 6A

SEE MORE QUESTIONS