A motorcycle driving a solid circular steel shaft transmits 20kW of power at 300 rpm. If the diameter of the shaft is 20 mm. Determine the maximum shear stress in the shaft.

Q: Determine location of centroidal x and y and the moment of inertia Ix of the figure shown. Use the…

A:

Q: IV. DATA AND RESULTS A. DETERMINING PACE FACTOR Тарed Mean Number of Pace Factor Trial Line Distance…

A: Note: Considering taped distance as 50 m for part B Given data, Pace factor (PF) = 0.6459 m/pace…

Q: 4. A 25-ft-diameter concrete caisson is to be sunk to the rock surface shown in Figure 5.17 at a…

A: Consider the free body diagram;

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

A:

Q: 3: Determine the magnitude of the Maximum shear force in the beam Vmax = 7.5 kNO Vmax = 50 kNO Vmax…

A:

Q: FUNCTIONS OF RICS

A: The Royal Institution of Chartered Surveyors (RICS) is an authorized professional association…

Q: 11. Determine the moment of inertia of the fully- cracked transformed section, I (in 10 mm). 12.…

A:

Q: 50. What should be the height (m) of a lighthouse, so that it can be visible from a distance of 3…

A:

Q: hree samples of Soll were collected dauring soll exxploration for of a Highrise Building a) Choose…

A: Solution: Three samples of Soil were collected during soil exploration for the construction of a…

Q: DEFLECTION AT POINT C IN mm Your answer DEFLECTION AT POINT B IN mm Your answer SLOPE AT POINT D…

A: EI = 80x103 N/mm2 x 154 x 106 mm4         = 12320 x 109 Nmm2          = 12320 KNm2

Q: Calculate the support reactions at A and B for the loaded beam Assume P = 41 lb, w 86 lb/ft, a= 2.5…

A: Given data : Uniformly varying load (w)=86 lb/ftUpward Point load (P)=41 lba=2.5 ftb=4.5 ft

Q: 223. The block shown in Fig. P-223 is acted.upon by its weight W horizontal force Q 3 600 lb, and…

A: Given data- W = 200 lb Q = 600 lb Resultant R of these forces is up and parallel to the incline.

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 3750 mm² and an…

A: Given Area and stress in rod 1 is 3750 mm2 and 160 mpaArea and stress in rod 2 is 3750 mm2 and 140…

Q: Vill pela fomonte Batama VELIKATEe min htt Spring 500 # 750 T PERNI # 250" VERKS Draw V&M diagrams…

A: Given:Required:Shear and moment diagram

Q: Figure, Y-axis 1cm Icm R=2cin C.9 X-axis

A:

Q: Points 1 2 3 4 5 6 B.S a d I.S b e f F.S c g H.I ارتفاع الجهاز 31.46 31.46 31.46 30.2 30.2 30.2 R.L…

A: Given values: Points B.S I.S F.S H.I R.L 1 a     31.46 29.3 2   b   31.46 28.9 3 d   c…

Q: Question 3: Use the method of Sections to determine the bar forces for the members BC, BG, and HG.…

A:

Q: solve the problem 4

A: Given data in question  Loads Span 7.5 m Simply supported beam  To find out  Moment at A and B

Q: The characteristics of the synthetic textile wastewater are 1500 mg/L BOD, 2000 mg/L SS, 30 mg/L…

A: Given: Textile plant: BOD = 1500 mg/l SS = 2000 mg/l Nitrogen = 30 mg/l Phosphorous = 0   Domestic:…

Q: Determine the reactions and draw the shear and moment diagrams for the following structure by using…

A:

Q: The structural steel column shown in figure below is fixed at its base and free at its upper end. At…

A: Data Given: Load P = (15 + 0.05R) = (15 + 0.05(78)) = 18.9 kip   Eccentricity e = 9 in.  Elastic…

Q: a. A 40-ft long (into the page) Tainter gate is shown below. It is being used by the U.S. Army Corps…

A:

Q: 10.55 Water (60°F) is pumped from a reservoir to a large, pressurized tank as shown. The steel pipe…

A: Calculate the velocity through the pipe:V=QAQ= 1 ft3/sA=π4D2=π44122=0.0873 ft2V=QA=10.0873=11.459…

Q: Determine all the zero-force members of the roof truss shown in the 5 kN 6 kN D B E H G F

A:

Q: A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left…

A:

Q: A water pipe ABC (i.e. A to B to C) comprises two (2) straight sections. AB is horizontal tapering…

A: Water pipe ABC Portion AB ---- Horizontal Diameter of pipe at A (dA) = 300mm = 0.3m Diameter of pipe…

Q: (8.) Draw the following network: a. G follows F but precede H b. G follows D but precede J c. M…

A: To draw the network

Q: 1. It is desired to remove the spike from the timber by applying force along its horizontal axis. An…

A:

Q: 12

A:

Q: 60 A square shallow foundation is to be constructed over a layer of sand. Given Df = 1 m; No is…

A: Given; Df = 1m ; qnet = 350 Kn/m2  sand is normally consolidated

Q: Refer to the following diagram. 1. Indicate the reaction forces at each thrust bearing (No…

A: (1). Consider the free body diagram

Q: for the following ODE near x 3x²y" - xy + y = 0

A: Given:- x=0 3x2y"-xy'+y=0 To find:- y(x)

Q: 2. Find P for the built-up column shown. Use A36 steel ( F, = 36 ksi ). The length is 19 ft-6 i and…

A: The given data is: A36 steel, Fy=36 ksi Length=19 ft-6 in=19.5 ft K=1.0 E=29000 ksi  Section…

Q: 1. Determine the reactions and draw the shear and bending moment diagrams for the structures shown…

A:

Q: a) The radius (R) b) The tangent length (T) c) The external distance (E) d) The middle ordinate (M)…

A: Given: The intersection angle is, ∆=30.375 The station of the PI is, PI=22+69.77

Beams and Frames

A beam is a horizontal structure or a member which is always subjected to transverse shear loads.