A model of submarine is scaled down to 1/25 of the prototype and is to be tested in a wind tunnel. The speed of the prototype at which we are to estimate the drag is 10 m/s. The ratio of the drag between the model and the prototype is = 1.21 x 10-2 cm²/s, Vair = 1.64 x 10-1 cm²/s and Psea water = 1027 kg/m³. Pair = 1.34 [Take Vsea water kg/m³]

A model of submarine is scaled down to 1/25 of the prototype and is to be tested in a wind tunnel. The speed of the prototype at which we are to estimate the drag is 10 m/s. The ratio of the drag between the model and the prototype is = 1.21 x 10-2 cm²/s, Vair = 1.64 x 10-1 cm²/s and Psea water = 1027 kg/m³. Pair = 1.34 [Take Vsea water kg/m³]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider a flow of SAE 30W oil through a 12-cm-diameter pipe. For SAE 30W oil, take p=891kg/m³. u= 0.29 kg/m-s at 20 °C, and μ = 0.01 kg/m-s at 100 °C, and π = 22/7. 4. For what flow rate in m³/h would a transition to turbulence take place at 100°C? Round the answer to one decimal place. The flow rate is m³/h.
A block is kept at rest at shown in figure. The coefficient of friction between the contact surfaces is 0.6. For the applied load of 20 N, the acceleration (in m/s²) of the block is (g = 10 m/s²). 5kg 20 N
The 2-kg spool S fits loosely on the inclined rod for which the coefficient of static friction is μ = 0.29. (Figure 1) Figure 0.25 m s ▸ Part A If the spool is located 0.25 m from A, determine the maximum constant speed the spool can have so that it does not slip up the rod. Express your answer to three significant figures and include the appropriate units. Value Submit Provide Feedback 4 Request Answer Units ?
A small boat weighing 40 LT has a submerged volume of 875 ft3 when traveling at 20knots in seawater. (ρ = 1.99 lb-s2/ft4 ; 1 LT = 2240 lb) a. Calculate the magnitude of the hydrostatic support being experienced by boat.b. What other type of support is the boat experiencing?c. Calculate the magnitude of this other type of support.d. What will happen to the submerged volume of the boat if it slows to 5 knots? Explain your answer.
A floating house will be projected as shown in the figure. The basement of the house will be in the form of an open concrete box. The height of the concrete box will be 0.60 m above the water surface. All other dimensions of the wooden house will be chosen by you. Other assumptions will be made by you if necessary. Compute the weight of concrete box, weight of house and the total weight of the system for 4 people living in the house. Wood 0.60m Concrete
An air stream flows over a smooth plate with Reynolds number of 106. The boundary layer can be assumed to be turbulent over the entire plate. If the length of the plate is increased by 10%, taking all the factors same, what is percentage change in the total drag coefficient? [Take (1.1)0.2 = 1.019]
The cylinder with 12cm height and diameter 10cm in figure is balanced by a 2-kg mass on the beam scale when the cylinder is immersed in 20°C water. What is the specific gravity of the cylinder?
A flat plate of area 2.5 x106 mm² is pulled with a speed of 0.6m/s relative to another plate located at a distance 0.15 mm from it. Find the force and power required to maintain this speed, if the fluid separating them is having viscosity as 0.2 Ns/m².
1. Compute the R1 value in newton for the beam 2. Compute the R2 value in newton for the beam 3. Compute the midspan value of Ely for the beam in two decimal places and in terms of kN-m³
An elevator weighting 1000 kg attains an upward velocity of 4 m/sec in two sec with uniform acceleration. The tension in the supporting cables will be