Consider a flow of SAE 30W oil through a 12-cm-diameter pipe. For SAE 30W oil, take p=891kg/m³. u= 0.29 kg/m-s at 20 °C, and μ = 0.01 kg/m-s at 100 °C, and π = 22/7.4.For what flow rate in m³/h would a transition to turbulence take place at 100°C? Round the answer to one decimal place.The flow rate ism³/h.

Answered: Image /qna-images/answer/d0b6e861-eee2-4d66-896e-48fd3996c3ff.jpg

Considera flow of SAE 30W oll through a 12-cm-diameter pipe. For SAE 30W oil, take p=891kg/m³, p=0.29 kg/m-s at 20 °C, and = 0.01 kg/m-s at 100 °C, and 17 = 22/7. For what flow rate in m³/h would a transition to turbulence take place at 100°C? Round the answer to one decimal place. The flow rate is m³/h.

Considera flow of SAE 30W oll through a 12-cm-diameter pipe. For SAE 30W oil, take p=891kg/m³, p=0.29 kg/m-s at 20 °C, and = 0.01 kg/m-s at 100 °C, and 17 = 22/7. For what flow rate in m³/h would a transition to turbulence take place at 100°C? Round the answer to one decimal place. The flow rate is m³/h.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical circular stack 30 m high converges uniformly from a diameter of 6 m at the bottom and 4.5 m at the top. Gas with a unit weight of 0.12 N per cubic meter enters the bottom of the tank with a uniform velocity of 0.334 m/sec enters the stack. The unit weight increases by 7.5 percent every 2 meters. Find the velocity of flow at every 5 meters along the stack. Graph velocity at the abscissa against height at the ordinate (PLEASE USE COMPLETE SOLUTION AND FIGURES)
Analysis this graph and explain the relationship between the friction factor and Reynolds number
I need the answer as soon as possible
I need the answer to the question in fluid mechanics
Assuming the data given in the following table, calculate turbulence effect in horizontal well for reservoir permeability K= 5 md. Pe 2500 psi μ Z m(p) (psia) (cp) Pwf 1500 psi 0 re 3000 ft 14.7 0.998 0.0127 1.70E+04 0.3 ft 400 0.960 0.0130 1.28E+07 h 100 ft 8,00 0.925 0.0135 5.13E+07 1,200 0.895 0.0143 1.14E+08 L 1500 ft T 150 F 10 % 1,600 0.873 0.0152 2.00E+08 2,000 0.860 0.0162 3.06E+08 2,250 0.856 0.0169 3.81E+08 2,500 0.857 0.0177 4.61E+08 2,750 0.860 0.0185 5.45E+08 3,000 0.867 0.0193 6.33E+08 0.02 CP 0.92 0.75 3,150 0.872 0.0197 6.87E+08 1 Ф H Z Yg Well Skin
mater 3
answer is given just give the solution and right answer.
Correct answer else downvote.
Hello , can I get an answer please?
A water pipe having a 2.33 cm inside diameter carries water into the basement of a house at a speed of 0.887 m/s and a pressure of 241 kPa. If the pipe tapers to 1.27 cm and rises to the second floor 7.37 m above the input point, what are the (a) speed and (b) water pressure at the second floor? (a) Number i Units (b) Number i Units
3) An incompressible flow velocity field is given as 1 1 [m/s] r r where r is in meters. (a) Calculate the mass flow rate through the cylindrical surface at r =1 m from z = 0 to z =1 m as shown in Figure A (b) Show that mass is conserved in the annular control volume from r = 1 m to r = 2 m and z = 0 to z = 1 m as shown Figure B a 2 m. I m 1 m 1 m 1 m