A small boat weighing 40 LT has a submerged volume of 875 ft3 when traveling at 20 knots in seawater. (ρ = 1.99 lb-s2/ft4 ; 1 LT = 2240 lb) a. Calculate the magnitude of the hydrostatic support being experienced by boat. b. What other type of support is the boat experiencing? c. Calculate the magnitude of this other type of support. d. What will happen to the submerged volume of the boat if it slows to 5 knots? Explain your answer.

Q: 50. In the figure below, the waterline section of a 1500 kN barge is as shown. Its center of gravity…

A: We have to calculate metacentric height against the rolling axis.

Q: m 2 ate for the support reactions of the following bea 60 KN 40 kN/m 120 kN m The 3 m D min

A:

Q: A floating cylindrical buoy of height h= 472mm and radius r= 44.7mm is made up of two materials. Its…

A:

Q: Situation 1. Consider the framing plan shown below in Fig.1. Given the following details: x =…

A: Simply Supported Beam : A simply supported beam is having two supports each at end of the beam and…

Q: Compute the magnitude of the resultant force on the indicated area and the location of the centre of…

A:

Q: The buoy is made from two homogeneous solid shapes each having a radius of 1.5 ft. The bottom is a…

A:

Q: Situation 3 The beam shown in the figure 14 is loaded by a concentrated load P and a uniformly…

A: Use equilibrium equations to find out reactions at support. Draw BMD & pick up maximum bending…

Q: Problem #2 Suppose a vertical flat plate supports water on one side and oil of specific gravity 0.86…

A:

Q: 1. For the pulley system shown, M₁ has a mass of 42 kg and an associated coefficient of friction of…

A:

Q: Find the magnitude of the force P

A:

Q: A rectangular box is floated. Outer dimensions 2m by 10m and has 2m high sides and weighs 4.9N. It…

A:

Q: compute the support reaction, for the beam ABCDE shown in following figure

A: Given that,

Q: Compute the midspan value of Ely for the beam loaded as shown in figure 1 m 600 N/m 5 m

A:

Q: Part A : Replace the loading by a single resultant force and determine its magnitude Part B :…

A: The given figure is shown below:

Q: A beam-spring system is shown L = 5m EI-2.5 × 10³ kN-m² figure below. heee 000 k = 40 kN m-10 kN k=…

A: For given spring-beam system,Initial displacement of 5 mmInitial velocity: 135 mm/sto find the…

Q: Analyze the following figure if: h=1.5 m, d=3.2 m, x=2.4 m 4.5 kN D 4.5 kN 4.5 kN h B 2 kN 2 kN h E…

A: Given:-

Q: The cross section of a concrete dam is as shown.  For the dam section of 1m width, plot the…

A:

Q: detailed

A: Given  x=3m max moment =18kN-m   For max w  Hogging moment 18kN-m   For max P Sagging moment 18kN-m

Q: termine the reactions at support and thne forces acting on each member. By applying 1 uni oad…

A: In addition to its initial horizontal speed, a projectile's horizontal displacement depends on its…

Q: A 1m x 1.5m cylindrical tank is full of oil with SG=0.92. Find the force acting at the bottom of the…

A:

Q: A cantilever beam supports the variable load shown. Calculate the supporting force RA and moment MA…

A:

Q: A continuous beam loaded as shown figure. Assume El is constant. Use any method to determine the…

A:

Q: A vehicle is to be propelled by a jet of water impinging on a vane as shown in Figure 4.7. The jet…

A: This problem is solved using Momentum_impulse Equation.  At point A, the velocity is resolved into…

Q: 10. In stable equilibrium for completely submerged bodies what is the relation between forces? a)…

A: Fb=W and the the centre of buoyancy is above the centre of gravity.

Q: A thin plate with infinite span is set at a positive angle of attack in a supersonic airstream. The…

A: Given that, P2P1=1+2.8θP2=1+2.8θP1 From Bernoulli's equation, ∆P=P2-P1=ρV22

Q: A 25-mm diameter shaft with density 7,870 kg/m³ is pulled through a cylindrical bore as shown. Oil…

A:

Q: I. Problem Solving: Answer the following and show your complete solutions. Round off your final…

A:

Q: THE CONCRETE DAM SHOWN WEIGHS 23.6 Kn/m' AND REST ON A SOLID FOUNDATION. DETERM THE MAXIMUM…

A:

Q: 3. A 0.2 kg mass rests on top of a spring that has been compressed by 0.4 m. The force constant for…

A:

Q: A block(unit weight = 19.5 kN/m^3) 0.56m square and 395mm deep floats on a stratified liquid…

A:

Q: 3. The drum has a weight of 100 lb and rests on the floor for which the coefficient of static…

A:

Q: 6. A concrete dam is shown below with its dimensions. Use unit weight of concrete of 23.50 KN/m3.…

A: To Find :- 1. Total hydrostatic pressure 2. Righting moment 3. Factor of safety

Q: L = 100 ft. A 100-ft long dam holds 30 ft of water as shown in the figure. w.s. a. Using the panel…

A:

Q: Determine the upward thrust F on .5 the semi-cylindrical top of the container shown below. The…

A:

Q: A body has a cylindrical upper portion of 4 m diameter and 2 m deep. The lower portion is a curved…

A: Diameter=4m  Depth =2.4m Total water displaced=4.5ton To find metacentric height

Q: The areas of the pistons in a hydraulic machine are 5cm² and 625cm². What force on the smaller…

A: Areas of pistons- A1=5 cm2 A2=625 cm2 Load F1=1250 N, It is needed to find the Load F2.

Q: Example 37: Replace the force and couple moment system acting on the beam in Figure (a) by an…

A: Solution Given that

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.