A microprocessor uses RAM chips of 1024x1 capacity. How many chips will be required and how many address lines will be connected to provide capacity of 1024 bytes. How many chips will be required to obtain a memory of capacity of 16 K bytes. (5) (i) (ii)

A microprocessor uses RAM chips of 1024x1 capacity. How many chips will be required and how many address lines will be connected to provide capacity of 1024 bytes. How many chips will be required to obtain a memory of capacity of 16 K bytes. (5) (i) (ii)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2. A microprocessor has a memory space of 4 MB. Each memory address occupies one byte. a) What is the address bus size (number of bits needed for addressing) of this microprocessor? b) What is the range (lowest to highest, in hexadecimal) of the memory space for this microprocessor? c) Complete the memory map by the address ranges (lowest to highest, in hexadecimal) 8 bits for each memory chip. 0x 0x 0x 0x 0x 0x 0x 0x Address 0 1MB 1MB 1MB 1MB
Question: Q) Interface An 8086 Microprocessor With Total Memory Size 128KB Using RAM Chip .Size...
Suppose we have 1G × 16 RAM chips that make up a 32G × 64 memory that uses high interleaving. (Note: This means that each word is 64 bits in size and there are 32G of these words.)1. a) How many RAM chips are necessary?2. b) Assuming four chips per bank, how many banks are required?3. c) How many lines must go to each chip?4. d) How many bits are needed for a memory address, assuming it is word addressable?5. e) For the bits in part d, draw a diagram indicating how many and which bits are used for chip select, and how many and which bits are used for the address on the chip.6. f) Redo this problem assuming that low-order interleaving is being used instead.
1. How do the data retention characteristics of RAM and ROM storage devices differ? 2. What is the purpose and use of the Program Counter (PC), Stack Pointer (SP), and Memory Address Register (MAR) registers? 3. Write an 8085 program to store 4EH in memory location 2840H and store 3EH in memory location 2841H, exchange them and store the result in memory locations 2842H and 2843H respectively. Solve this problem using three different methods. 4. Write a program to exchange the content of memory locations [2801] [2800] with [2803] [2802]. 5. The following program is supposed to add the contents of memory location 2050h to the Accumulator. The program works correctly only part of the time. Show that it is wrong to execute the program and how to correct it. MOV LDA ADC HLT В.А 2050H в 6. In a multibyte addition program, when you must use the ADD instruction? When you must use the ADC instruction? 7- The 8085-instruction set does not include a clear accumulator instruction. Which…
A ROM chip with a 128Kx8 organization has _______ memory locations. A.128 B.138 C. 128k D. 17
Design a 512 k byte memory using 64 k byte chips. Show the internal design of the 64kbyte chips.
Draw the figure for memory segments with 8086 microprocessor software model. Explain the logical address structure used for each segment (Explain which registers are used in logical address presentation of each segment; segment address : offset address). Give an example solution to find the physical address in a segment from the logical address for 8086 microprocessor.
A memory chip from a digital camera has 25 bistable (ON-OFF) memory elements. What is the total number of ON-OFF configurations?
Assume that the microprocessor can directly address 1M with a and 8 data pins. The maximum RAM system can design by using the following RAM chips is given in the below table. Choose the correct option:(provide answer in details) (a) None of them (b) 25K x 8 (c) 27K x 8 (d )26K x 8 (e) 24K x 8
None
a.Write the addressing modes of the following instructions: (i) MOV A, @R0(ii) MOVX @DPTR, A (iii) MOVC A, @A+DPTR (iv) MOV R0, #45H b) Write instructions to perform the following operations: (i) Move the content of Accumulator to register 7(R7).(ii) Move the contents of RAM memory location 55H to Port 1(iii) Receive content from ROM Memory location 200H into Accumulator.(iv) Clear bit 7 of the Accumulator.c) Why 4-20mA Current loop is widely used Industrial Standard for sensor data transmission and control. What are its advantages over 0-12V Standard? d) Two configurations of GPIB is shown in Fig. A and Fig. B. Explain the working of GPIB in both the configurations and what are the differences between the two. this question is asked in microcontroller and microprocessor
b) The number of addressed words in a ROM is determined from some fact. 92 X 8 ROM architecture support those facts? Whát will be the capacity?