A member is subjected to the loads shown in Figure 3. The loads are 30% dead load and 70% live load. K = Ky = 1.0. Use A992 steel and select a W12 shape (the lightest option). Hints: The amplification factor B₁ can be estimated as 1.0 for choosing a trial selection. Then when calculating the actual B₁, use Cm = 1.0 (transversely-loaded member). 60 k

A member is subjected to the loads shown in Figure 3. The loads are 30% dead load and 70% live load. K = Ky = 1.0. Use A992 steel and select a W12 shape (the lightest option). Hints: The amplification factor B₁ can be estimated as 1.0 for choosing a trial selection. Then when calculating the actual B₁, use Cm = 1.0 (transversely-loaded member). 60 k

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Q2: Verify that the steel section W12 x 106 can be used for the cantilever beam shown in the Figure (2). Check for flexural strength and deflection only. The beam has lateral support at the ends. The service uniform distributed load includes, wp = 6 k/ft dead load and w₁ = 3 k/ft live load. Use steel A992 and C₁ = 1. A -10 ft- B Fig. (2)
Read the question carefully and give me the right solutions with clear calculation.
For the built-up shape shown, determine:A) the elastic section modulus and the yield moment (b) the plastic section modulus and the plastic moment Mp.Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa
For the given properties of beam below. Design the reinforcements of the beam. d'=75 mm b=400 mm d=580 mm fc'=35 MPa fy=320 MPa Mu=1000000000N mm Input is 0 in As' if compression bars are not needed. A. USE NSCP 2001, As = mm2, As' = mm2 B. USE NSCP 2015, As = mm2, As' = mm2 %3D
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
AW10x30, 3.1 m long A36 steel is used as a column with fixed ends to support a service dead load of 267 kN. Calculate the maximum service live load the column can sustan uning LRFD Use theoretical value of k. Write your answer rounded to the nearest whole number in KN Use properties Ag = 5.703 mm2, rx = 111.25 mm, ry = 34.8 mm. Use stored value. Asnwer in 5 decimal places.
An A36 angle bar is used as a tension member connected on both legs with 18 mm. Given that s = 74 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. 40 50 L6 x 3½x%o] 56 62.5 Ag = 1,852 mm2 t= 8 mm
Q19: In Figure below, what is the ratio of P to F h Waer Hinge Sec A-A
I need the answer as soon as possible