A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft is required. a) Make the dimensional decisions for a 49-mm basic size with a medium drive fit for the hub and shaft, and specify dimensions with tolerances for the shaft and the hub bore for the fit. b) When the interference pressure "p" is at a minimum (p at Smin) for the specified tolerances how much torque (in Nm) can be transferred with the medium drive fitted assembly if the steel to steel friction is 0,8 and the hub of the length is 170 mm. E=207 GPa

A medium drive of a steel hub of a gear with an outside diameter of 80 mm on a steel shaft is required. a) Make the dimensional decisions for a 49-mm basic size with a medium drive fit for the hub and shaft, and specify dimensions with tolerances for the shaft and the hub bore for the fit. b) When the interference pressure "p" is at a minimum (p at Smin) for the specified tolerances how much torque (in Nm) can be transferred with the medium drive fitted assembly if the steel to steel friction is 0,8 and the hub of the length is 170 mm. E=207 GPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.Please design a pair of spur gears in the milling machine. It is known that power input is 7.5kW, Ni 1450r /min, and the %3D transmission ratio is required to be u = 2.08. F1. If there is slight impact, the supplementary conditions for trial design of this pair of gears: primary selection k = 1.8, number of smaller gear teeth Z1 = 26. The allowable stress and factors for material %3D is: [0]= 600 MPa, [o„]z= 599 MPa, [0,]ı= 220 MPa, [0,]= 213 MPa. E=1.693, Z, =1898/mpa Z„ = 2.5 K =1.25 Ky =1.1 K K =1.2 На K =1.35 Y =2.65, Y = 2.28 Y =1.58 Y =1.76 %3D Fa2 Fal sa1
Keino Thompson Problem 1. Given 2 parallel shalts with Required : h₁ = 3001pm d₁ N₁ = T₁ = + e = a) N₁ & N₂ b) p = center distance of 12.7 cm h₂ = 0.2 h₁ P = N₁ d₁ Power = = W d₂ Circular pitch of 10 teeth 2 Hp (Transmitted to pulley 2) gears in c) ng in rpm d) Pitch line velocities of Gears 1&2 of pulley 2 e) Torque in nm
1-Show how the roughness is indicated for a Surface to be coated, obtained by any production method with N6 showing max. and min roughness. 3- gearing is suitable for two shafts at 90°. : Draw five turns of a compression spring of wire diameter 6mm, pitch 12 num and outside diameter of 38mm.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
2. The following data is for the gear train shown in the figure: Given: N2 = 30t, N3 = 35t, N4 = 55t, N5 = 40t, N6 = 50t, N7 = 40t %3D w2 = 30 rpm ccw, warm = 20 rpm cw, Input torque on gear 2 is 1200 lbf.in Determine the following: a. Angular velocity of the sun gear. b. The gear ratio R required to determine the angular velocity of gear 6. c. The angular velocity of gear 6. d. The angular velocity of gear 7. e. Output torque on gear 7. Be careful with your units. Arm 6 ... 7
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
B) A simply supported shaft is shown in the following Figure. A constant magnitude distributed unit load p is applied as the shaft rotates. The shaft is also subject to a steady torque of Tmax 2000-N -m., find the diameter of shaft required to obtain a safety factor of 2.5 in fatigue loading if the shaft is steel of Sut 814 MPa and Sy 703 MPa. The dimensions are in cm, the distributed force in N/cm, and the torque is in N-m. No stress concentrations are present, the shaft is machined, the required reliability is 90%, and the shaft operates at room temperature Figure: 1= 20-cm: b = 18-cm ; a = 16 cm Applied distributed load p:= 1000 N em ; 区区

For a pair of standard gears, the module is m=2.5mm，pressure angle is α=20 0. ha*=1. c*=0.25. The teeth number on gear 1 is z1=22. The standard center distance is a=68.75mm. Find the following parameters of gear 2: the teeth number, z2 = ( ) the diameter of reference circle, d2=( )mm the diameter of addendum circle da2 =( )mm the diameter of dedendum circle df2 =( )mm
Ex] A double-threaded right-handed worm gear transmits 15 Hp at 1150 rpm. The pitch of the worm is 0.75 inch and the pitch diam of 3 inches. The pressure angle is 14.5° and the coefficient of friction is 0.12. a) Find the tangential force on the gear. b) Find tangential force on worm. c) Find the separating force Solution: (To be discussed by the Instructor during the lecture period)
A pinion shaft of a machine transmits a torque of 68 Nm to the shaft of gear at a speed of 574 rpm, which is input at pinion gear and its shaft rotates in the clockwise direction. The number of teeth on the pinion and the gear are 38 and 78 respectively, while the module is 6 mm. Assume a pressure angle of 200. Calculate: i) Power transmitted by the shaft of the pinion in W. ii) Torque on the shaft of the gear in Nm. iii) Speed ratio iv) Tangential load on the pinion in N
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio