A machine vice as shown in figure below ,has a single start square thread with 28 mm nominal diameter and 3 mm pitch. The outer and inner diameters of the friction collar are 62 and 50mm, respectively. The coefficients of friction for thread and collar are 0.3 and 0.3, respectively. The machinist can comfortably exert a force of 240 N on the handle at a mean radius of L= 217 mm. Assuming uniform wear for the collar, Calculate: a-Mean diameter of the screw d. b-Helix angle a. C- Friction angle o. d-Tightening Torque T in terms of W. e- Friction Torque Tc in terms of W. f-Clamping force developed between the jaws W. g- Overall efficiency of the clamp n. Fixed Moving jaw jaw Screw --- Frame Handle

A machine vice as shown in figure below ,has a single start square thread with 28 mm nominal diameter and 3 mm pitch. The outer and inner diameters of the friction collar are 62 and 50mm, respectively. The coefficients of friction for thread and collar are 0.3 and 0.3, respectively. The machinist can comfortably exert a force of 240 N on the handle at a mean radius of L= 217 mm. Assuming uniform wear for the collar, Calculate: a-Mean diameter of the screw d. b-Helix angle a. C- Friction angle o. d-Tightening Torque T in terms of W. e- Friction Torque Tc in terms of W. f-Clamping force developed between the jaws W. g- Overall efficiency of the clamp n. Fixed Moving jaw jaw Screw --- Frame Handle

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question No.16: A double threaded power screw with ISO metric trapezoidal threads with 15° semi-angle of thread is used to raise a load of 300 kN. The nominal diameter is 100 mm and pitch is 12 mm. the coefficient of friction at screw threads is 0.15. Neglecting collar friction, calculate; (i) torque required to raise the load, (ii) torque required to lower the load and (iii) efficiency of the screw.
The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with both sides of the plate being effective. The coefficient of friction is 0.25 and the maximum pressure is limited to 82 N/cm2. The ratio of diameters is 1.4. Assuming uniform wear determine: (You should upload the answers in the Link provided for submitting the assignment, typing the answers in the box provided below is optional). The internal diameter of the plate in mm The external diameter of the plate in mm
Question 3 A single square thread power screw is to raise a load of 50 KN. A screw thread of major diameter of 34 mm and a pitch of 6 mm is used. The coefficient of friction at the thread and collar are 0.15 and 0.1 respectively. If the collar frictional diameter is 100 mm and the screw turns at a speed of 1 rev/s. (Given dm = 31mm, 1 = 6mm, dc = 100mm). Find: (a) the power input to the screw. (b) the combined efficiency of the screw and collar.
A scissor jack is being designed with a single square thread that engages threaded collar G and rotates in a ball thrust bearing at D. The thread should have a mean diameter of 10mm and afeed (feed per revolution) of 3 mm. With a coefficient of friction of 0.20 for greased threads,a) Calculate the torque M on the bolt required to lift a 1000 kg load from the position shown andb) Calculate the torque M required to lower the load from the same position.Assume platform AB and line DG will remain horizontal under load.Neglect friction in the D-bearing.
i need the answer quickly
Answer detailly 3(i)
You have to build a box lifter, this will be made with a square threaded power screw. The power screw is 3 inches in diameter and 2 threads per inch. To improve the speed of raising and lowering the boxes, it must be with triple thread. The coefficient of friction of the screw and collar is 0.25, the diameter of the collar is 4 inches.Calculate:1. The depth of the thread, the width of the face, the average diameter, the root diameter, the pitch and its feed.
-- A double-threaded power screw with square threads pushes against a load of 3,822 N at a speed of 15 mm/s. The screw has a major diameter of 20 mm and a pitch of 6 mm. The frictional coefficient of the threads is 0.25, and collar friction is negligible. What is the rotational speed of the screw in units of revolutions per minute? Type your answer... 2 points
A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter is 20 mm and pitch is 5 mm. Assume that the friction on threads is 0.1. Determine the torque needed to turn the screw in N-m without considering collar torque.
Quickly please.
A double threaded Acme screw of 1.5-in major diameter is used in a jack to raise a 6.5 kip load. The jack has a plain thrust collar with 2.2-in mean diameter and the coefficients of kinetic friction are estimated as 0.12 for the collar and 0.15 for the screw. If the screw has the following parameters. lead 0.5 in, thread angle in the normal plane - 14.4, and mean diameter 1.375 in, determine the running efficiency of the jack in raising the load N] 35
A Machine vice has single start square threads with nominal diameter 22 mm and pitch 5 mm. Collar diameters are 55mm and 45mm respectively. Coefficient of friction for threads 0.15 and u for collar 0.17 The machinist can comfortably apply a force of 125N on handle of mean radius 150 mm. Assuming uniform wear theory calculate, (1) The clamping force developed between the jaws, (2) The overall efficiency of screw