A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height is 10.8 mm. The elastic modulus of steel is 207 GPa. (a) What are the bolt diameter (d) and pitch (p) for the bolt? (b) Determine a suitable length (L) of the bolt, rounded up to the nearest 5 mm? (c) If the total threaded length of the bolt LT = (2d +6) mm, how much of its threaded length will be in the grips? (d) If the effective tensile stress area of the bolt (A:) is 84.3 mm², calculate the bolt stiffness (kb). (e) Assume that the stiffness of each steel plate is 4,200 MN/m. Calculate the total member stiffness (km). (f) If the bolt is tightened with a force of 10 kN, what will be the stress in the bolt due to tightening? Is it a tensile stress, compressive stress or shear stress? (g) After tightening the bolt, a tensile force of 12 kN is applied on the plates, what will be the stress in the bolt now?

A M12 x 1.25 hex-head bolt with a nut is used to clamp two 25-mm thick steel plates. The nut height is 10.8 mm. The elastic modulus of steel is 207 GPa. (a) What are the bolt diameter (d) and pitch (p) for the bolt? (b) Determine a suitable length (L) of the bolt, rounded up to the nearest 5 mm? (c) If the total threaded length of the bolt LT = (2d +6) mm, how much of its threaded length will be in the grips? (d) If the effective tensile stress area of the bolt (A:) is 84.3 mm², calculate the bolt stiffness (kb). (e) Assume that the stiffness of each steel plate is 4,200 MN/m. Calculate the total member stiffness (km). (f) If the bolt is tightened with a force of 10 kN, what will be the stress in the bolt due to tightening? Is it a tensile stress, compressive stress or shear stress? (g) After tightening the bolt, a tensile force of 12 kN is applied on the plates, what will be the stress in the bolt now?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The answer is one of the options below please solve carefully and circle the correct option Please write clear .
The radial distance measured from the pitch circle of a gear to the bottom of the gear tooth is known as the addendum of a gear. Select one: True False
Determine the x, y, z components of reaction at the journal bearing C if 0 = 0°.
Which one of the following medals has the lowest density? tungsten aluminum magnesium titanium
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
If Gear C and gear A are having the same pitch diameter gear and gear B is twice (larger) the diameter of gear C. If gear C is turning at the speed of 50 RPM, what would be the Rotational speed of Gear B in RPM. (RPM = revolution per minute)
Bolt material is 304 stainless steel. frame material is Aluminum. kindly assume all the other values and find the bolt size / diameter for bolt. write all formulas and explain the procedure. there are 2 bolts 1 on left and 1 on right.
please help on the below question.....not that there are 2 imagies
Which of these expressions represents the value of G for a 90 degree elbow if the degree of fit is 45 degree, the radius of the welding elbow is 10 inches, and the outside diameter is 14 inches. A - 45x(10+7) B - 45x(10+14) C 45x(10x7)
A hole is to be drilled as shown by the circle. Using the part geometry shown below, indicate on the part sketch where locator(s) should be positioned according to the 3-2-1 principle. Use dashed lines to indicate locators on hidden surfaces. Also indicate where clamping force(s) should be applied using arrows. Use the minimum number of clamping forces.
Q.7 Degree of freedom at triple point is A В D -1
11 A circular gear turns 240 per hour. Through how many radians does it turn in a 24-hour day?