A load W is to be lifted using the crane BC which is hinge at B as shown in the figure. Neglecting the weight of the crane, determine the largest weight that can be lifted if the maximum force of cable AC is 100KN. (kN) 40 KN 45 Oeg 10.0 m 80m 47.98 60.42 55.33

A load W is to be lifted using the crane BC which is hinge at B as shown in the figure. Neglecting the weight of the crane, determine the largest weight that can be lifted if the maximum force of cable AC is 100KN. (kN) 40 KN 45 Oeg 10.0 m 80m 47.98 60.42 55.33

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explain it correctly
Problem 3: A sailor is being rescued using a boatswain's chair that is suspended from a pulley that can roll freely on the support cable ACB and is pulled at a constant speed by cable CD. Knowing that a = 30° and ß = 10° and that the combined weight of the boatswain's chair and the sailor is 250 lb, determine the tension in the support cable ACB (ignore the tension in cable CD). D A at C B B
Consider the three-dimensional structure shown in the figure, fixed to the ground at point O, and restrained by cables AB and CD. The tension T in the restraining cable CD is 3.1 kN. Calculate the magnitude of the vector moment (in kNm) produced by the force exerted by the cable CD on point C, about the point O (assume use of the right-hand rule). Take a = 4.8 metres, and b = 3.8 metres. b (m) 3 m C a (m) 4 m D *y 4 m
A 100N load is supported by a strong bar as shown in the figure. The tension in the cable is 200N. The value of the axial force in the strong bar in N. ... 10 m 200N 10ÖN LA ZB 10 m 224.54 542.42 C. 342.54 145.42 174.45 254.24 452.24 H) 245.42
A propped beam shown below is loaded with UDL along its entire span. Determine the following: (Mc) C. a. Determine the reaction (R) b.Determine the end moment at wall d. Determine the tangential deviation at point B with respect to point C (t B/C) Determine Өвс A * R 4kN/m 3M
solve for the tension at cable AB and the reaction at E, considering the weight of bent bar CBDE = 420 lb *pls use 3 decimal places all throughout the solution
A oil rig tower is held in equilibrium by three ropes. The tension in cable AD is tightened until it reaches 7600 N. B d3 da ds do d₁ d2 Z E D d5 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value d₁ 8.5 m d₂ 18.5 m 16.5 m 30 m 9 m 80 m a. Determine the magnitude of the force/tension in cord AB, TAB. b. Determine the magnitude of the force/tension in cord AC, TAC. c. Determine the magnitude of the force developed along the tower, FAE- → i. Hint: FAB= (0+03+ FAER) KN. Round your final answers to 3 significant digits/figures. The magnitude of the force/tension in cord TAB is The magnitude of the force/tension in cord TAC is The magnitude of the force developed along the tower FAB is kN kN kN
Given the propped beam with an internal hinge as shown in the figure, what is the maximum safe value of w (in kN/m) if the absolute maximum shear produced is 70 kN? (input a positive value only) Hint: RA = RD and Rg = 8.25w (kN). %3D Use equations instead of diagrams. w(KN /m) A qm BO4SM 4,5M OD internal hinge
statics of rigid bodies
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension T in cable CD? T 3.3' Answers: LCD = TCD= i A 46° B 46 lb ft. lb D
7-115. The 80-m-long chain is fixed at its ends and hoisted at its midpoint B using a crane. If the chain has a weight of 0.5 kN/m, determine the minimum height h of the hook in order to lift the chain completely off the ground. What is the horizontal force at pin A or C when the chain is in this position? Hint: When h is a minimum, the slope at A and C is zero. B Asseccons 60 m Prob. 7-115
The beam showed below is carrying a weightless cable that carries a cylindrical load weighing 1631kg. Using unit load method, determine all the support reactions and the deflection and rotation on the free end of the beam. Given El=32x10ʻkN-m² 2.5EI 25KN/m 60° 2m 2m 2m;El 1631kg