A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17200 ksi] rods, and a solid steel [E = 31400 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.53 in. Assume L₁=45 in and L₂=67 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied.

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17200 ksi] rods, and a solid steel [E = 31400 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.53 in. Assume L₁=45 in and L₂=67 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: The bar 1 is bronze alloy with elasticity The cross section area of bar 1 is The bar 2 is aluminum…

Q: Pravinbhai

A: The objective of the question is to calculate the deflection at pulley B and point C of a steel…

Q: ods (1), and a solid steel [E = 200 GPa] rod (2), as shown in the figure. All rods are unstressed…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: A copper bar with rectangular cross-section is hung from a rigid pin that is supported by two steel…

Q: 1. A rod of length 1.50 m and diameter 0.12 m is mounted in a rigid wall A vertical bar of length…

A: INTRODUCTION : In order to solve the above problem, the maximum shear stress theory is applied when…

Q: Rigid bar ABCD is loaded and supported as shown. Bars (1) and (2) are unstressed before the load P…

Q: P2 D A B P1 P2 D, dz

Q: Tutorial Question on Axially Loaded Members Question One A steel bar 2.4 m long has a circular cross…

A: Approach to solving the question: using the formula for elongation of stress region and the…

Q: Consider the bar in Figure 2, which has cross-sectional area A = 1-10-3 m², modulus of elasticity…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E=…

Q: What, if any, are the stresses at point O? NOTE THAT WE ARE NOW ASKING ABOUT POINT O. Choose all…

A: When a bar is subjected to various loads then there are different types of stresses developed in the…

Q: mm. The normal stress in the aluminum rod must be limited to 124 MPa, and the normal stress in the…

A: From the given data:

Q: SITUATION 3: The Fig shows a circular steel plate supported on 3 posts A, B, and C which are equally…

Q: The solid 32 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the…

A: To Find : The shaft deflection at pulley A and C. Given : The load P and Q are P=850N ,Q=1000N.…

Question

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17200 ksi] rods, and a solid steel [E
= 31400 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.69 in. and they are symmetrically positioned relative to the
center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.53 in. Assume L₁=45 in and L₂=67 in. If all bars are unstressed
before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 16 kips is applied.
(1)
Answers:
01
02 =
i
i
L2
(2)
Save for Later
B
P
eTextbook and Media
(1)
ksi.
ksi.
L₁
Attempts: 0 of 5 used
Submit Answer

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Concept used is mentioned

VIEW

Step 2: Procedure and calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E-73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 12 mm and a length of L₁ - 2.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 22 mm and a length of L₂ - 1.7 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P - 80 KN is applied to the rigid bar. L₁ Answer: 0₁- i 0₂- 164 L2 (1) (1) MPa MPa
A steel bar with a uniform cross section is fixed at both ends. A load P = 2.5 kips is applied at point C. The bar has a cross-sectional area of 8 in2.Calculate the reactions at joints A and B and the displacement at joint C. Assume that the modulus of elasticity E = 29,000 ksi.
Rigid bar ABCD is supported by a smoth pin at D and by vertical aluminum alloy [E=10,000 ksi] bars attached at joints A and C. Bar (1) was fabricated to its intended length L1=40 in. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2=59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by Δ=0.12 in. After bar (2) has been stretched and connected to the pin at C, a load P=20 kips is applied to the rigid bar at B. Use the following additional properties and dimensions: A1=A2=0.75 in2, a = 36 in, b =54 in, and c = 48 in. Determin: a) The normal stresses in bars (1) and (2). b) The deflection at A of the rigid bar.
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.50 in. and a wall thickness of 0.219 in. is fastened to a solid 2.00-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=10 kips, L1=6 ft, L2=7 ft, and L3=7 ft. (A) Calculate the cross-sectional area of steel tube (1), A1, and the cross-sectional area of the aluminum rods (2) and (3). in inches squared (B) Find the force in the steel tube (1), F1, and the forces F2 and F3, which are the forces in the aluminum rods. Use the correct sign for each force. By convention, a tension force is positive, and a compression force is negative. IN kips (C) Find σ1, σ2, and σ3, the normal stresses in members (1), (2), and (3), respectively. By convention, a tension stress is positive, and a compression stress is negative. IN KSI (D) Determine δ1 and δ2, the deformations of members (1) and (2), respectively. By…
Rigid bar ABCD is loaded and supported. Bars (1) and (2) are unstressed before the load P is applied. Bar (1) is made of bronze [E= 100 GPa] and has a cross-sectional area of 400 mm2. Bar (2) is made of aluminum [E= 70 GPa] and has a cross-sectional area of 600 mm2. After the load P is applied, the force in bar (1) is found to be 60 kN (in compression). Determine: (a) the stresses in bars (1) and (2).(b) the vertical deflection of point A.(c) the load P.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 10 mm and a length of L₁ = 2.7 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 25 mm and a length of L₂ = 1.7 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 70 KN is applied to the rigid bar. L₁ B Answer: 01 = i 0₂ i L2 (2) (1) (1) MPa MPa
Define the term Zero slope?
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 14100 ksi] rods, and a solid steel [E = 28000 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.61 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.47 in. Assume L₁-39 in and L2-72 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. O (1) A Answers: 0₁ = i 0₂ = i L2 (2) B P ksi. ksi. L
Question 6 A B 112 mm 1.2 m 0.9 m Figure 6 The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of A992 steel: a. Find the vertical and horizontal component acting on the pin of the pulley C. b. Find the compressive force in the rod BD. c. Find the effective length-factor for BD. d. Express the radius of gyration about any centroidal axis for a solid circular area as a function of the diameter of a circle. e. Find the critical effective slender ratio (KL/r), according to the AISC specifications. f. Determine the required minimum diameter of the A992 steel solid circular rod BD to the nearest mm as allowed by the AISC specifications. g. Determine the F.S. for buckling of the designed rod DB. -0.9 m P