A liquid of density p is filled in a vessel of cross- sectional area A. The vessel has a hole of cross-sec- tional area a at a depth h below the free surface of the liquid. When the hole is unplugged, the liquid comes out of the hole with a velocity v. The volume of liquid coming out of the hole per second is Q. The reaction force exerted on the vessel by the emerging liquid is (assume A >> a)

A liquid of density p is filled in a vessel of cross- sectional area A. The vessel has a hole of cross-sec- tional area a at a depth h below the free surface of the liquid. When the hole is unplugged, the liquid comes out of the hole with a velocity v. The volume of liquid coming out of the hole per second is Q. The reaction force exerted on the vessel by the emerging liquid is (assume A >> a)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Super Soaker XP30 is a marvel of hydraulic dispersion weaponry. By pumping on the handle, you charge the chamber to high pressure. The pressure is maintained until you pull the trigger at which point the water (? = 1000 kg/m3) is released at high velocity.You have charged your pressure chamber to an absolute pressure of P1 = 697500 Pascals, much higher than today's outside air pressure of 101300 Pascals. The pressure chamber is location at a height of y1 = 0.103 meters above the exit point. The exit point has a small opening with radius r = 0.0033 meters.Determine all the following:The velocity at which the water exits the Super Soaker: v2 = m/sThe mass flow rate through the exit: kg/secThe volume flow rate through the exit: m3/secNOTE: You may treat the water chamber as a "tank" and approximate the water velocity there to be zero.
An open cylindrical container of radius R with a thin liquid layer of density p at the bottom, is rotating at a constant angular velocity w. As a result of the rotation, the liquid is displaced clearing a circular area at the bottom of the container or radius R/2. Determine the height of the liquid, H, on the cylindrical wall. R/2
1. Water is being discharged through a 5-mm diameter hole on the side and lowermost portion of a full 200-liter cylindrical tank with a height of 1 meter. Determine the initial velocity of the water jet as it is ejected from the tank. 2. A hot air balloon is filled with heated air and weighs only about one-half of what air weighs under identical conditions. The buoyancy force, which can be expressed as Fp= PairgVbaloon will push the balloon upward. If the balloon has a diameter of 10 m and carries a 70 kg person, determine the acceleration of the balloon when it is first released. Assume the density of air is 1.16 kg/m³, and neglect the weight of the ropes and the cage.
The balloon has a mass of 30 g (empty) and it is filled with air having a temperature of 20 °C having the density of 1.202 kg/m³. If it is released, it begins to accelerate upward at 8 m/s?. (Figure 1) Part A Determine the initial mass flow of air from the stem. Assume the balloon is a sphere having a radius of 260 mm Express your answer using three significant figures. I1 vec ? m = g/s Figure 1 of 1 Previous Answers Request Answer Submit X Incorrect; Try Again; 4 attempts remaining 8 m/s? Provide Feedback 5 mm
VII. Suppose water is leaking from a tank through a circular hole of area A, at it's bottom. When water leaks through a hole, friction and contraction of the stream near the hole reduce the volume of the water leaving the tank per second to cAp 2gh where c(0
A lead ball of radius 5 cm is immersed in water. Calculate the thrust it undergoes. Consider the density of water as 1000 km/m^3. The formula for the volume of the ball is V=3/4 πr^3
3. Consider the shown configuration where water Pump from a large, open reservoir flows through the pipe Water and discharges to atmosphere. When the pump is not running, it does not prevent water from flowing Pipe Spring through the pipe. At this state, the force that develops in the spring is 1000 N. However, when the pump is running, the force in the spring becomes 3000 N. The diameter of the pipe is 0.1 m. Neglecting all frictional effects, determine the power delivered by the pump to the fluid. Pwater 1000 kg/m³.
In a container of diameter Φ (see image), a tube of diameter ε (much smaller than the diameter of the container) is connected at a height d. The water level in the container is h. Water flows at a constant speed in the tube. The density of the fluid is ρ. If the container is open to the air, calculate the pressure at the connection. Conceptual question: In the second figure of the image, three pressures are represented. Are these pressures constant along the height they describe?
A pneumatic tube system is used in a hospital to quickly transport laboratory samples across the building. A cylindrical canister (radius r = 12.5 cm, mass m = 950 g) containing the sample is placed in a tube with roughly the same radius. The bottom of the tube is exposed to atmospheric pressure, but the portion of the tube above the canister is maintained at a slightly lower pressure, which sucks the canister into the tube. For the questions below, use 101,325 Pa for atmospheric pressure, and maintain 6 significant figures on your numerical answers. What absolute pressure P must be maintained in the portion of the tube above the canister in order to keep the canister stationary? (For simplicity, assume that the tube is coated with a non-stick surface so that friction can be ignored). What is the gauge pressure above the canister in the scenario described above? If tube system operator lowers the absolute pressure found in part (a) by 1.00%, then what is the acceleration of the…
Assume that 87 kg of fuel are burned by a rocket per second. If the exhaust gases have a speed of 2.8 x 103 m/s, what is the thrust in N on the rocket?
Milk with a density of 970 kg/m^3 is transported on a level road in a 9-m long, 3-m diameter cylindrical tanker. The tanker is completely filled with milk, i.e., no air space in the tank. If the truck is accelerating from a stop signal at 7.0 m/s^2 to the left, determine the pressure difference between the maximum and minimum pressures in the tank. Depict on the figure the location of the minimum and maximum pressures in the tank. min. 9m 3m
We would like to calculate the minimum pressure required to force plasma from the heart to the top of the head. For this analysis we will assume blood is a Newtonian, incompressible fluid. The distance from the heart to the top of the head is 0.5m. Assume the density of plasma to be 1065 kg/m3. The vein diameter is 0.95 mm. Assume friction can be neglected.