Initially tank I and tank II each contains 100 gal of brine, tank I having 200 lb salt and tank II 50 lb of salt in solution. Brine runs at 2 gal/min from tank I to tank II through one pipe and at 3 gal/min from tank II to I through another pipe. The brine is kept well stirred. How much salt (in lb) will be in the second tank after 50 min?

Q: A 7-hp (shaft) pump is used to raise water to an elevation of 15 m. If the mechanical efficiency of…

A:

Q: From pump 1.0 m 1.5 m a. Using a vertical bar chart, plot the pressure drop (i.e. P₁-P₂) for these…

A:

Q: The large water truck pictured (4.8 foot diameter by 12 foot long tank) releases water through a 3…

A: Here we will apply simple fluid dynamics equation.

Q: Find the force required to hold the plug in place. The water discharges freely into the atmosphere…

A: water velocity v=3m/sentry diameter D=0.25mplung diameter d=0.2mto find the force required to hold…

Q: A burst of water go out horizontally through a hole near the bottom of the tank as shown in Figure…

A:

Q: t t=0, it is filled with 31.4 m3 of water. The radius of the tank is 1 m and its height is 10 m.…

A: Hydrostatic Pressure varies vertically inside a fluid. As height from free surface decreases…

Q: b) At time t= 0 the height of water in the tank is h0. Find an expression for the height as a…

A: For the solution refer below images.

Q: if the velocity of a liquid is 1.65 ft / s in a 12-inch diameter conduit. What is the velocity in a…

A:

Q: A trough is 6 feet long and 11 foot high. The vertical cross-section of the trough parallel to an…

A: Given trough is 6 feet long and 11 foot high.Assume vertical section of through is represented by…

Q: A tank is filled with water at a rate of 9 gal/min as shown in the figure below. Given that D = 3 ft…

A: Given A tank is filled with water at a rate of 9 gal/min as shown in the figure below. Given that D…

Q: Determine the relationship between the air pressure in the tank and the maximum height to which the…

A:

Q: A water system of 2 inches (inside diameter) pipe, having a length of 1/4mile, is to be flushed with…

A: Given Data: The inside diameter of the pipe is, d=2 in=2 in×ft12 in=16 ft. The length of the pipe…

Q: n the Picture above OBE locm /Bc = 2Scm Ehe Vtelve of nŋ or rotation cl dao rem Convert this vawe to…

A:

Q: What is the relation between temperature and viscosity for hydraulic oil?

A: The viscosity parameter shows the resistance offered by the particle of a liquid to flow.  Let…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.