3. Consider the shown configuration where water Pump from a large, open reservoir flows through the pipe Water and discharges to atmosphere. When the pump is not running, it does not prevent water from flowing Pipe Spr through the pipe. At this state, the force that develops in the spring is 1000 N. However, when the pump is running, the force in the spring becomes 3000 N. The diameter of the pipe is 0.1 m. Neglecting all frictional effects, determine the power delivered by the pump to the fluid. Pwater 1000 kg/m³.

3. Consider the shown configuration where water Pump from a large, open reservoir flows through the pipe Water and discharges to atmosphere. When the pump is not running, it does not prevent water from flowing Pipe Spr through the pipe. At this state, the force that develops in the spring is 1000 N. However, when the pump is running, the force in the spring becomes 3000 N. The diameter of the pipe is 0.1 m. Neglecting all frictional effects, determine the power delivered by the pump to the fluid. Pwater 1000 kg/m³.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2. The jet engine on a plane flying at 160 m/s in still air draws in air at standard atmospheric temperature and pressure through a 0.5-m-diameter inlet. If 2 kg/s of fuel is added and the mixture leaves the 0.3-m-diameter nozzle at 600 m/s, measured relative to the engine, determine the thrust provided by the engine. 160 m/s
Assuming that the fluid enters to the pump with no shock / no swirl, construct the velocity triangles at both inner and outer diameters of the impeller for the case where the blade angle at the outlet is: β2 = 90o, and β2 = 130o
Following the pump, the pressure in a 6-inch inner smooth pipe conveying water is 20 pounds per square inch (psia). The water is released into a 100- foot-long open tank located from the pump. Prove that the rate of discharge of water in cubic feet per second (ft3/s) is 3.58 ft3/s. Note: use the following formula of Churchill Equation; 1 = -4log ( + _0.27 E +0.9] %D `Re
0.540 kPa of Nitrogen gas is contained in a certain vessel. It is fed into the unit at 1 kPa by a certain fan connected to the container tank. 0.120 kPa is the lost at the suction line while and 0.270 kPa at the discharge side. The flow velocity at the exit is 10 m/s. Assume the density of nitrogen gas to be 1.17 kg/m³. Find the pressure developed by the fan. Select the correct response: 1 psi 0.224 psi 0.132 psi 0.331 psi
A jet engine on an airplane moving at 950 km/hr has an exit area of 0.5 m². If gas exiting the engine has a speed of 1950 km/hr (relative to the jet engine) and a density of 0.5 kg/m3, how much thrust does the engine produce? If the airplane has 2 identical engines (producing the same thrust) what is the total thrust produced by this aircraft?
A generator on a research aircraft requires 0.2 slugs per second of cooling air. A cooling air scoop for the generator is designed to be operated while the aircraft is cruising at 200 mph at 20,000 ft above sea level in standard atmospheric conditions. The scoop connects to an opening on the generator casing that has an area of 2 ft2 . Determine the required area of the inlet of the scoop. Also determine the air velocities and pressures at the scoop inlet and at the connection with the generator casing.
Water at 22oC is pumped from the bottom of a large storage tank where the pressure is 290 kPa gage to a nozzle which is 14.17 m above the tank bottom and discharges to the atmosphere with a velocity in the nozzle of 20.1 m/s. The water flow rate is 50 kg/s. The efficiency of the pump is 77% and 9 kW are furnished to the pump shaft.a. Draw the diagram b. The friction loss in the pump. c. The friction loss in the rest of the process.(include principles used)
The lawn sprinkler shown in the figure rotates in the horizontal plane. A water flow of 15 L/min of water enters the center vertically and discharges in the horizontal plane from the two jets. Determine (a) the torque needed to keep the sprinkler from rotating and (b) the rotating speed of the sprinkler when the torque is removed. d = 5 mm R = 225 mm
The gauge pressure of water at A is 150.5 kPa. Water flows through the pipe at A with a velocity of 18 m/s, and out the pipe at B and C with the same velocity v. Neglect the weight of water within the pipe and the weight of the pipe. The pipe has a diameter of 50 mm at A, and at B and C the diameter is 35 mm. Pw = 1000 kg/m³. (Figure 1) %D Determine the x component of force exerted on the elbow necessary to hold the pipe assembly in equilibrium. Express your answer to three significant figures and include the appropriate units. View Available Hint(s) HẢ ? Value Units %3D Submit Previous Answers
A fire hydrant supplies water under a pressure of 190 kPa. A 100-mm-diameter hose is connected to it at A and the hose extends 40 m to the fire truck inlet at B. B Part A Determine the pressure of the water as it arrives at B. The friction loss is 1.5 m for every 10 m of hose. The inlet at Bis 0.5 m higher than the hydrant outlet. Express your answer to three significant figures and include the appropriate units.
Obtain an expression for the volume flow rate at the exit of the mixing chamber in terms of the volume flow rates of the two inlet streams and the rate of heat transfer to the mixing chamber.
A jet issued of water at the rate of 200 L/s and a velocity of 36 m/s strikes a blade moving in the same direction at 15 m/s. The deflection angle of the blade is 120°. Neglecting friction, determine: (a) the x- and y-components of the force exerted by the jet on the blade in N.; (b) the work done by the jet on the blade, in joules.