The rotor rotates at a constant angular velocity of w-130 rad/sec. although the fluid initially approaches the rotor in an axial direction, the flow across the blade is primarily outward as shown in figure 1. Measurements indicate that the absolute velocity at the inlet and outlet are V1-16 m/s and V2=18 m/s, respectively. Is this device a pump or a turbine? T4-60 A= 60° † (2) (2) 2=0.2m (1) -0.1m (1) =130 rad/s -Blade- Figure 1

The rotor rotates at a constant angular velocity of w-130 rad/sec. although the fluid initially approaches the rotor in an axial direction, the flow across the blade is primarily outward as shown in figure 1. Measurements indicate that the absolute velocity at the inlet and outlet are V1-16 m/s and V2=18 m/s, respectively. Is this device a pump or a turbine? T4-60 A= 60° † (2) (2) 2=0.2m (1) -0.1m (1) =130 rad/s -Blade- Figure 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 2) A pressure of 10 kPa gage is applied to the surface of water in a tank. There is an outlet 0.5m below the surface of the water. What is the velocity of the water exiting the outlet into the air? You may assume that the velocity of the water leaving the outlet is much much faster than the velocity of the water level dropping inside the tank. 10 kPa gage 0.5 m
A 3-bladed wind turbine with 250 kW generator has diameter of 50 m and tower height of 60 m. It is designed to have Cp of 0.25 at wind speed of 12 m/s when regulation starts. The cut-in and furling Speeds for the machine are 5 m/s and 20 m/s respectively. Mechanical and electrical efficiencies are 90 % and 95 %. By assuming the density of air as 1.225 kg/m3. Calculatea. What is power developed by the rotor at 12 m/s when regulation starts? b. If the tip-speed ratio at this wind speed is 4.2, then what is the rpm of the rotor? c. Calculate the actual torque developed. d. Calculate the maximum possible annual power output.
6.5-7
Convert 50 kPaG into meters
An air compressor absorbs 1000 kg of air per hour at a pressure of 100 kPa and 500 kPait presses on the pressure. Specific volume of air at compressor Inlet 0.8 m3/ kg, at Exit0.2 m3/ kg dir. The internal energy of the air at the outlet is 100 kJ/kg more than at the inlet.60 000 kJ/h heat transfer occurs from the compressor to the air. Kinetic and potential energyfind the power needed to operate the compressor, neglecting its changes.
A pump is supplying water at the rate of 4ft^3/s it lifts water to a height of 15ft. Determinte the power that the water is being delivered to by the pump (hp). If the pump has 80% efficiency , find the power that needs to be supplied to the pump (hp)
Find an expression for the rate of change of the mass of water in the tank.
PLEASE ANSWER QUICKLY
Water is being pumped from an atmospheric source on the ground at the rate of 200 liter/minute to a pressurized tank on top of an office building through a constant diameter pipe. The discharge to the pressurized tank is 20 meters off the ground and the tank has a gauge pressure of 5 bar. Ignoring frictional losses, determine the a)power the pump must supply the fluid in W (Correct Answer is 2321 W) By performing an energy balance around the pump and ignoring friction and any changes in height between the inlet and outlet of the pump determine the: b) increase in pressure across the pump in psi (Correct Answer is 101 psi)
Water with a mass rate of "M" continuously enters a tank with a diameter of "D". If a hole in the bottom of this tank allows water to escape, find the maximum height of the tank.
1- A centrifugal fan supplies 4.7m3/s of air at a total static pressure of 325Pa. If the fan efficiency is %60 and rotates at a speed of 950rpm and supplies air with a velocity of 12m/s, determine the fan total pressure, air power, and fan power? Ans. 411 Pa