A line was determined to be 2395.25 m when measured with a 30-m steel tape supported throughout its length under a pull of 4 kg at a mean temperature of 35°C. Tape used is of standard length at 20°C under a pull of 5kg. Cross-sectional area of the tape is 0.03 cm? Modulus of elasticity is 2x106 kg/cm2

A line was determined to be 2395.25 m when measured with a 30-m steel tape supported throughout its length under a pull of 4 kg at a mean temperature of 35°C. Tape used is of standard length at 20°C under a pull of 5kg. Cross-sectional area of the tape is 0.03 cm? Modulus of elasticity is 2x106 kg/cm2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the question. Note: This is the complete question. If any data missing please assume it
Q4/ A 50 m steel tape with a cross-sectional area of 13 mm and weight of 0.122 kg per meter. The tape is hanged under a tension force of 115 N at 40°c to measure a distance equal to 2560m. During the measurement, the tape was found to be 2 cm too long. This tape has been made under a tension force of 24.6 kg and 20°c. Calculate the correct distance knowing that a=0.000018 m/c, E = 2.11*10 kg/cm', g 9.81 m/s.
Which among the following determines the direction of closing error? Oa. Tan δ = Σι/ΣΟ b. Tan d = = [L²/[D² c. Tan 8 = [D/[L d. Tan 8 = [D²/>L²
A 50-m steel tape weighing 0.035kg/m isconstantly supported at mid-length and its endpoints, and is used to measure a line AB with asteady pull of 6.5kg. If the measured length ofAB is 1200.00m, determine the following:a. Correction due to sag between supports andfor the whole tape lengthb. Total sag correction for the whole lengthmeasuredc. Correct length of line AB
draw the SF and BM diagrams along with qualitative deflected shapes
A 50 m tape of standard length has weight of 0.05 kg/m, cross section is 0.04sq cm, E is 2.10 x10 6 kg/sq cm. The tape is of standard length under a pull of 5.5 kg when supported throught its length. This tape was used to measure a distance AB and was recorded to be 458.65 m. at time of measurement the pull applied was 8 kg with the tape supported only at its endpoints and temperature observed was 18°C. Find the sag correction for the measured line
two images attached.
A steel tape is 100.00 ft long and has a weight of 0.0225 lb/ft and is used to measure a line from A to B in two segments (one full tape length and one partial tape length), supported at the ends only for each of the two segments. The recorded distance is 181.83 ft. The pull at the time of measurement is 12 lb. What is the length of the line corrected for sag? (Assume that no other tape corrections need to be applied.)
I WILL RATE! Determine the Vertical Deflection at C. Indicate the negative sign if the answer is downward.
Q2 calculate the Vertical movement of point A 4 m t Steel wire D = 25 m E = 20X10 +4 + 4.1 2 4 20KN Steel wis D = 60 E 20x10 2m + 3 kľu 60 A 60 kuu
Help pls. Ill upvote. Answer should be in 4 decimal places, Thankyou :)
Given that L = 179 mm, P = 18 N and Q = 63 N. Replace the two couples shown with a single equivalent couple, specifying its magnitude and the direction of its axis. %3D B 120 mm F 144 mm 120 mm, E P C. 192 mm D.