A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 660 kg and an average gear-tooth force of 2.90 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 135 mm, R = 555 mm, 0 = 23° Detail of contact at B A Answer: x = i B- R G mm

A large symmetrical drum for drying sand is operated by the geared motor drive shown. If the mass of the sand is 660 kg and an average gear-tooth force of 2.90 kN is supplied by the motor pinion A to the drum gear normal to the contacting surfaces at B, calculate the average offset of the center of mass G of the sand from the vertical centerline. Neglect all friction in the supporting rollers. Assume r = 135 mm, R = 555 mm, 0 = 23° Detail of contact at B A Answer: x = i B- R G mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question #02 Please provide justified answer asap to get a upvote
12. Data communications a. analog methods uses: b. digital methods c. either of the above d. neither of the above
Talk N Text all al a O N 89I 1l:48 TNT Final Assignment_Rigid Bo... I. GENERAL INSTRUCTIONS 1. Do this BY PAIR or individually. Write your name/s. Submit this only once. 2. Draw the figure to illustrate your understanding of the problem (as required). 3. Show complete formulas and solutions. 4. No rounding off in the solutions, only your final answer should be rounded off to 3 decimal places. In cases where the answer in a sub question will be used for the following sub question, use the non-rounded value. 5. Enclose your final answer in a box. No extra answers. 6. File submissions should be in single PDF. 7. Once you submit your solution papers late, your score will automatically be reduced by half, regardless of how late you are (1 min or more). Presentation matters. II. Problems Problem 1 Given: Mass of canister: 4000 kg Mass of beam BD: 50 kg Max allowable force: 1. AB = 2. CD = 30 kN 30 kN 3. EF = 34 kN 4. GH = 34 kN Determine the greatest allowable acceleration of the system.…
D /5 = Question 8 of 15 < View Policies Current Attempt in Progress Two forces are applied to the construction bracket as shown. Determine the angle which makes the resultant of the two forces vertical. Determine the magnitude R of the resultant. Assume F₁700 lb, F₂ = 460 lb, a = 56° F₁ F2 H ***
Homework 7: Q1/ Two identical bars A, E, L find location of pin (B). C Answer PL 2AE cos 02 0 10 B P
What is the maximum applied load this structure can support before it fails due to yielding (i.e. if 18 kN force was increased, how high could it go)? What is the maximum applied load if the material was changed to Ti-6Al-4V (Grade 5) titanium?
Don't copy & correct solution
METERS | FEET MODEL: IA6BJM SIZE: 8" x 6" x 13" RPM: 1750 PRESSURE MAX: 120 PSI 76+250 GRAPHIC 61+200 Ø13," (75 HP) SCALE. 70% 75% 80% 82% 83% 60 GPM Ø12%" (60 HP) 84% 83% 82% 80% 46+150 Ø12%" (50 HP) 75% 70% 65% A 100 BHP Ø11%" (40 HP) 31+100 010%" (30 HP) NPSHr ft m 75 BHP 60 BHP 30+9 15+50 50 BHP 3О ВНР 40 BHP 20+6 NPSHR 10+3 GALLONS PER MINUTE LITERS PER MINUTE Refer to the system curve drawn on this pump curve. If the pump is to move 1200 gpm, what is the estimated NPSH Required by the pump (ft)? 1136+300 2271+600 006+2ODE 4543+1200- 5678+1500- 6414+1800아 7949+2100- 9085+2400- 11356+3000야 10 FEET
solve the problem in the picture, please
See photos for full question
ASAP
i need the answer quickly