A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. a. Determine the dimension b (inch.) so that the joint is as strong as the boards. 1.75 in. a. 38.33 c. 11.67 b. 12.25 d. 40.25 b. Determine the dimension t (inch.) so that the joint is as strong as the boards. 5.75 in. a. 0.477 c. 1.50 b. 1.60 d. 0.510

A joint is made by gluing two plywood gussets of thickness t to wood boards. The tensile working stresses are 1200 psi for the plywood and 700 psi for the boards. The working shear stress for the glue is 50 psi. a. Determine the dimension b (inch.) so that the joint is as strong as the boards. 1.75 in. a. 38.33 c. 11.67 b. 12.25 d. 40.25 b. Determine the dimension t (inch.) so that the joint is as strong as the boards. 5.75 in. a. 0.477 c. 1.50 b. 1.60 d. 0.510

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The working stresses for the manufactured wood beam are 10 MPa in bending and 1.4 MPa in shear. Determine the largest allowable value of the load intensity co. 25 mm Wo 25 mm -3 m 6 m- 200 mm 1 250 mm 25 mm
1. Three metal strips, each 40 mm height, are bonded together to form the composite beam shown. The modulus of elasticity is 210 GPa for the steel, 105 GPa for the brass, and 70 GPa for the aluminium. If the allowable bending stress for the aluminum (Gallow)al= 100 MPa, for the steel (Gallow)s=150 MPa and (Gallow)b= 200 MPa for brass determine the maximum allowable intensit of w of the uniform distributed load. 2w Aluminum 2w 10 mm Brass 10 mm Steel 20 mm 2m - 40 mm
The structural efficiency in managing bending, shear and for steel vs concrete
Two wood boards, each 18 mm thick, are joined by the glued finger joint shown. The finger joint will fail when the average shear stress in the glue reaches 1080 kPa. Determine the shortest allowable length d of the cuts if the joint is to withstand an axial load of P = 4.2 kN. Use a = 18 mm and b = 144 mm. d Glue b P P Answer: d = i mm
The composite shaft shown consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 N-m is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N 235 mm (1) B 165 mm Partial Ans: Max shear stress in Member 1 is 55.7 MPa 270 N-m (2)
4
What will be the moment of resistance of the composite section shown in the figure below if the permissible stress in wood and steel is 70 N/mm2 and 120 N/mm2 respectively. Steel plate Wood -200- 10 150 400 126 20
4
Help
Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible normal stress in the glue is limited to 100 MPa. The maximum safe load that can be applied at the joint is P+ 40° 60 mm P
The two pieces of wood, 2 in. by 4 in., are glued together along the 40o joint. Determine the maximum safe axial load P that can be applied if the shear stress in the glue is limited to 250 psi