A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2" piston and 1.5" rod, and a 16" stroke length. What flow rate (in gpm) is required to extend the press in 6 seconds?Answer: 2.2 ± 1 A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2" pistonand 1.5" rod, and a 16" stroke length. What flow rate (in gpm) is required to extend the press in 6seconds?Your Answer: 0.36IncorrectThe answer is 2.2 ± 1.

Given:The force applied by the hydraulic press, The diameter of the piston, The diameter of the rod,…

A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2" piston and 1.5" rod, and a 16" stroke length. What flow rate (in gpm) is required to extend the press in 6 seconds?

A hydraulic press is used to apply 500 lbs of force to press fit an assembly. The cylinder has a 2" piston and 1.5" rod, and a 16" stroke length. What flow rate (in gpm) is required to extend the press in 6 seconds?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The team is rolling a 300-mm-wide strip 25-mm thick with two powered rolls each of radius = 250 mm and with entrance speed = 16m/min. The work thickness is to be reduced to 22 mm in one pass at a roll speed of 50 rev/min. The work material has a flow curve defined by K = 275 MPa and n = 0.15, and the coefficient of friction between the rolls and the work is assumed to be 0.12. a. Determine if the friction is sufficient to permit the rolling operation to be accomplished. b. Calculate the roll force. Roll speed, v, R= roll radius c. Calculate the roll torque and horsepower. -p-roll pressure d. Exit velocity under the assumption that the plate widens by 3% during the operation. L= contact length e. Calculate the forward slip. f. Why it is recommended to use 4-high or cluster mills to perform the rolling operation? Figure 1: Rolling process. g. Discuss the options to improve the process and write your recommendation to the team.
1. A six-cylinder two-stroke engine with a compression ratio = 9 produces a torque of 1100 Nm at a speed of 2100 rpm. It has a bore bof 123 mm and a stroke s of 127 mm. (a) What is the displacement volume and the clearance volume of a cylinder? (b) What is the engine bmep, brake power, and mean piston speed?
A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3and a piston stroke length of 675 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
A mechanical press is used in a forging operation of a 13.5mm in diameter cylinder. The press is powered by a 26.4kW motor at a velocity of 308 mm/s. The yield stress is 104MPa and the coefficient of friction is 0.249 a) Determine the maximum force that can be exerted in this operation. b) If the cylinder is forged to a diameter of 28.928.9 mmmm, determine the final height of the cylinder. Urgent
The length of the inserted leg is (500) mm, the length of each step in it is (1) mm, and the length of the vernier scale (98 mm) Divided into (50) sections, how accurate is it?
A petrol engine produces 250 kW while using 1.014 kg of fuel per minute. The fuel has a lower heating value of 45000 kJ/kg, and the engine has bore of 100 mm and the stroke-to-bore ratio of 1.2. The clearance volume of the cylinder is 1.178×10° mm². The friction power is found to be 10% of the power that engine produces. Sketch (your own) the simple neat and clean block diagram of the engine, clearly indicating the control volume and control surface, with all the given data displayed on it. For air take the value of y= 1.4. Determine the following: (a) The brake thermal efficiency (N th). (b) The indicated thermal efficiency (Nind,th )- (c) The mechanical efficiency (7mech ). (d) The brake engine efficiency (7,). (e) The indicated engine efficiency (7,nd). (Hint: Engine efficiency is a function of how the ideal work or power is calculated. Frequently, the air-standard cycle is used for calculating the theoretical work.) NOTE (Q 4): Use standard symbols and write units is each and every…
Please help. Written on paper not typed on computer please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
You are asked to design a four cylinder four-stroke compression ignition engine for light trucks, which is required to provide a maximum brake torque of (2.000x10^2) Nm at the rated speed of (4.50x10^3) rpm. The bore (B)/stroke (L) ratio is required to be (9.0000x10^-1). Given that the bmep of the engine is assumed to be (1.0000x10^3) KPa, find its stroke (L). The answer should be in the unit of meter with 3 significant figures.
Q2) A differential band brake shown below transmits a torque of 450N.m. The coefficient of friction is N/0.28. The diameter of the druff of 400mm. its tensile yield strength is 50N/mm. the tensile yield strength of the lever is 58N/mm² and its width is the 1/3rd of its height, the allowable shear stress of the pin is 32N/mm². Determine: N (4-4099 T₂= N (a-899 ii. Hi. P= b 3099 b-309 b- 15.86 e- 3900 c- 300 c- 16.58 d. 1200) d-849) d-11.55) N (a-18.56 c- 6 iv. The thickness of the band t=. d-3) e-31 d-13) v. The width of the band w... vi. The thikness of the lever h d-30) d-25) vii. The width of the lever w=....... viii. The diameter of the pin d= ...... d- 18) mm (a- 2 mm (a- 23 .mm (a-20 mm (a- 10 mm (a- 12 <2² ه آعی b-5 b- 35 b- 30 b-15 b- 14 25 400 c-10 c-20 c-16 مع
5.) A double-acting 12-cylinder, 4-stroke cycle engine with a cylinder diameter of 240 mm operates at 2,400 rpm. The prony brake arm at 1.24 meters registered an equivalent braking load of 0.24 metric ton. Calculate the brake mean effective pressure in psi. the piston travels 1.24 times its diameter
0/ During the rolling process, the average flow stress is 20,000 lb/in², etermining the amount of reduction in the cross-sectional area (use n = 0.40 and K = 35,000 lb/in²).
Please help. Written on paper not typed on computer please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.