A hydraulic lift consists of two pistons that connect to each other by an incompressible fluid. If one piston has an area of 0.44 m2 and the other an area of 6.2 m2, how large a mass can be raised by a force of 290 N exerted on the smaller piston?
Q: The applied force to the small piston of a hydraulic press is 75.0 N. The area of the said small…
A: Given: Force applied to small piston F1 = 75.0 N Area of small piston A1 = 20.0 cm2 Force applied to…
Q: A raft is 4.20 m wide and 7.30 m long. When a horse is loaded onto the raft, it sinks 2.70 cm deeper…
A:
Q: A hydraulic lift raises a 2000 kg automobile when a 500 N force is applied to the smaller piston. If…
A:
Q: A hydraulic lift in a garage has two pistons: a small one of cross sectional area 5.00 cm squared…
A: In the question it is given that ,area of the small pistan, a1=5 cm2area of the large piston, a2=…
Q: The hydraulic oil in a car lift has a density of 8.46 x 10² kg/m³. The weight of the input piston is…
A:
Q: A cylindrical tank with a large diameter is filled with water to a depth D = 0.285 m. A hole of…
A:
Q: . A dentist's chair with a patient in it weighs 2500 N. The output piston of the hydraulic system…
A: Step 1: Step 2: Step 3:
Q: A hydraulic lift consists of two cylindrical pistons, one with a radius of 3.4 m and the other with…
A:
Q: Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and…
A: A) As per Pascal’s principle, Here, P1 and P2 are the pressures at the pistons of area A1 and A2,…
Q: Two pistons of a hydraulic lift have a radius of 5 cm and 11.5 cm respectively. If the input force…
A: in the case of hydraulic lift , pressure at both piston is same that is P1 =P2 P1 = input pressure…
Q: At a given instant A has the motion shown in (Figure 1). Figure 3 ft -1.5 ft- VA=3 ft/s -X A=6 ft/s²…
A: The disk doesn't slip. So that
Q: A hydraulic lift consist of two pistons that connect to each other by an in-compressible fluid. If…
A: 4.42 kg of mass can be raised by the given force
Q: A hydraulic lift has two pistons, large (d=300mm) and small (d=15mm). A force of 500 N is exerted on…
A:
Q: In a simple hydraulic system piston 1 has a cross section area of 0.00050 m2 , and piston 2 has a…
A:
Q: In the hydraulic pistons shown in the sketch, the small piston has a diameter of 2.0 cmcm . The…
A: Sol. Given Diameter of the small piston (d) = 2 cm =2×10-2 m Diameter of the Big piston (D) =7 cm =…
Q: n the Netherlands, a dike holds back the sea from a town below sea level. The dike springs a leak…
A: Height, h = 3.25 mArea, A = 1.43 cm² = 1.43×10-4 m² = 0.000143 m²
Q: A raft is 5.70 m wide and 6.50 m long. When a horse is loaded onto the raft, it sinks 2.90 cm deeper…
A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: A certain hydraulic lift uses a piston of area 0.25 m^2 to push oil through the system on the other…
A: In case of hydraulic lift F1A1=F2A2 Putting all the values in the equation…
Q: (a) If the input cylinder of a hydraulic jack has a diameter of 5.00 cm and the output cylinder has…
A: To answer this question about a hydraulic jack, we need to apply the principles of hydraulics,…
Q: Consider the hydraulic lift shown in the figure. The small piston has an area A₁ of 0.0330 m², and…
A: Step 1:Step 2:Step 3:Step 4:
Q: A cylindrical tank with a large diameter is filled with water to a depth D = 0.356 m. A hole of…
A:
Q: the hydraulic lift (the figure below) has a small piston with the surface A1A1 = 0.032 m2 and a…
A:
Q: A barber raises his customer's chair by applying a force of 120 N to a hydraulic piston of area 0.01…
A: Given : Force = 120N Area of hydraulic piston = 0.01 m2 Area of…
Q: barber raises his customer's chair by applying a force of 150N to a hydraulic piston of area 0.01 m2…
A:
Q: A hydraulic lift in a garage has two pistons: a small one of radius 1.8 cm and a large one of radios…
A:
Q: Find the force P that must be applied to a piston of area 10.10 cm2 to produce sufficient fluid…
A:
A hydraulic lift consists of two pistons that connect to each other by an incompressible fluid. If one piston has an area of 0.44 m2 and the other an area of 6.2 m2, how large a mass can be raised by a force of 290 N exerted on the smaller piston?
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- In the hydraulic pistons shown in the sketch, the small piston has a diameter of 2.6 cmcm . The large piston has a diameter of 5.6 cmcm. How much more force can the larger piston exert compared with the force applied to the smaller piston?As shown in the figure below, a hydraulic system has two pistons of different diameter and uses a liquid of density ρ = 850 kg/m3. The smaller piston has a diameter of 2.1 cm and a mass of 1.6 kg and the larger piston a diameter of 14 cm and a mass of 3.5 kg. Determine h, the height difference between the two pistons.A hydraulic system consist of one cylinder that has a cross-sectional area of 6m2,connected to another cylinder that has a cross-sectional area of 32m2.A force of 12N is applied to the smaller cylinder. What force acts at the large cylinder
- A swimming pool has dimensions 26.0 m ✕ 7.0 m and a flat bottom. The pool is filled to a depth of 1.70 m with fresh water. (a) What is the force exerted by the water on the bottom? (b) What is the force exerted by the water on each end? (The ends are 7.0 m.) (c) What is the force exerted by the water on each side? (The sides are 26.0 m.)A raft is 4.80 m wide and 7.30 m long. When a horse is loaded onto the raft, it sinks 2.90 cm deeper into the water. (a) Calculate the volume of the water (in m3) that was displaced after the horse was loaded unto the raft. m3 (b) Given that the density of water is: 998 kg/m3, calculate the weight of the water (in N) that was displaced after the horse was loaded unto the raft. N (c) What name is given to the weight of the water that was displaced when the horse was loaded on the raft? Bernoulli's force Torricelli's force Pressure force Buoyant force (d) Determine the weight of the horse. NA certain hydraulic system is designed to exert a force 405 times as large as the one put into it. (a) What must be the ratio of the area of the slave cylinder to the area of the master cylinder? (b) What must be the ratio of their diameters? (c) By what factor is the distance through which the output force moves reduced relative to the distance through which the input force moves? Assume no losses to friction.
- A hydraulic lift is designed with an output cylinder that has 36 X the area of the input cylinder. If a force F is applied to the input cylinder, the output cylinder can supply a force equal to _______.Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and the large piston has an area A, of 4.00 m?. What force F2 will the large piston provide if the small piston is pushed down with a force F, of 18.0 N? Assume that the fluid used in the lift is incompressible. F, = F, y2 A, A, F,A cylindrical tank with a large diameter is filled with water to a depth D = 0.273 m. A hole of cross-sectional area A = 5.03 cm² in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole? (a) Number i (b) Number i Units Units
- A hydraulic jack piston has a diameter of 0.06 m. The hydraulic jack is connected to another piston that supports the load. The support load piston has a diameter of 0.50 m. If the jack can lift a mass up to 2500 kg, what is the maximum force that one needs to apply to the piston in order to lift the given mass?The diameters of the pistons on a hydraulic press are 5.0 cm and 40 cm. When a force of 50 N is exerted on the smaller piston, what force can the larger piston exert? {A = Bd2/4}Answer is in NewtonThe small piston of a hydraulic lift has a cross-sectional area of 3 cm, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg= 15 kN?