A hot isothermal surface is to be cooled by attaching an array of parallel, equally spaced vertical square plates, side length =405 mm, AT between hot surface and surrounding air is 45°C and the film temp = 50 °C, Air properties (k = 0.02735 W(m.K, a =2.487E-5 m /s, v=1.798E-5 m /s, Pr= 0.7228). If the optimum spacing is 12 mm, what is the heat transfer rate (watts) from the 12-plates? 12 : number of plates. %3D Select one: A. 527.70 B. 469.65 C. 591.02 D. 638.52 E. 411.61

A hot isothermal surface is to be cooled by attaching an array of parallel, equally spaced vertical square plates, side length =405 mm, AT between hot surface and surrounding air is 45°C and the film temp = 50 °C, Air properties (k = 0.02735 W(m.K, a =2.487E-5 m /s, v=1.798E-5 m /s, Pr= 0.7228). If the optimum spacing is 12 mm, what is the heat transfer rate (watts) from the 12-plates? 12 : number of plates. %3D Select one: A. 527.70 B. 469.65 C. 591.02 D. 638.52 E. 411.61

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem: A solid copper cube of 10-cm edge length(p =8954 kg/m³, c = 383 J/kg.K, k= 386 W/m.K) initially at a uniform temperature T;= 250°C is suddenly immersed in a well-stirred fluid which is maintained at a uniform temperature T = 50 °C. The heat transfer coefficient between cube and the fluid h=20O W/m²K. A. Check whether the lumped system analysis is suitable. B. Determine the temperature of the copper block at t= 5 min after the immersion. TE 250°C 10 cm Tm= 50 °C, h=200 w/mk
A 200mm diameter spherical steel ball initially at 500°C is rapidly immersed in an oil bath that is at 20°C. The convection coefficient is h = 600W/m²-K, and the steel ball has the following properties: c= 500J/kg-K, p= 7000kg/m³, k=30W/m-K. Determine the time taken (min) for temperature at the surface of the ball to drop to 100°C.
A 7 cm diameter bed on a 25 cm long bed, as shown in the figure below. The shaft rotates at 3200 revolutions per minute with uniform intervals of 0.2 mm. Continuous operation The temperatures of the shaft and bearing adjacent to the oil gap are 55 0C. your oil viscosity 0.05 N.s/m2 and its thermal conductivity is 0.17 W/m.K. Continuity, momentum and by simplifying the energy equations and solving for each separately, a) The maximum temperature of the oil, b) Calculate the heat transfer rates to the bearing and shaft.
A hot isothermal surface is to be cooled by attaching an array of parallel, equally spaced vertical plates, plates are of equal length and width =352 mm , the film temp =50 °C ,Air properties (k = 0.02735 W/m.K, a =2.487E-5 m/s, v=1.798E-5 m /s, Pr = 0.7228). What is the plate spacing (mm) that maximizes heat transfer from the array when AT between hot surface and surrounding air is 82°C?
Write the comparison between forced and free convection in a non-isothermal system?
Water at a temperature of T∞= 25°C flows over one ofthe surfaces of a steel wall (AISI 1010) whose temperatureis Ts,1= 40°C and thermal conductivity of steel is 671 w/m.k. The wall is 0.35 m thick, and itsother surface temperature is Ts,2= 100°C. For steadystateconditions what is the convection coefficient associatedwith the water flow?
I need the answer as soon as possible
What is the rate of heat loss from a heated horizontal pipe as a result of natural (free) convection that have a length of 1 m and surface temperature of 100 deg C, the ambient air is at 0 deg C and the diameter of the pipe is 0.1 m. Film temperature Tf averaged boundary layer temperature Tf=50 C. kf=0.03 W/m.K, Pr=0.7, v=2*10-5 m2/s, B=0.0031(1/K) Select one: a. 220.7985 b. 249.0378 c. 191.1709 d. 278.9799
i need the answer quickly
The rear window of an automobile is defogged by passing warm air over its inner surface. If the warm air is at Ti = 40°C and the = 30 W/m2-K, what are the inner and outer surface temperatures, in °C, of 4-mm-thick corresponding convection coefficient is h; window glass, if the outside ambient air temperature is To = -15°C and the associated convection coefficient is h, = 65 W/m²-K? o,0 Evaluate the properties of the glass at 300 K. Tsi i °C Ts,0 i °C
A block with thickness 2.3cm, and conductivity k-4W/mK is heated such that its temperature at its top is T₁-191°C Above the block, air at temperature Tair 22°C is blowing across the top which has a surface area of 1m² with heat transfer coefficient of 26W/m²K. air & W/mK T₁ T₂ What is the thermal resistance from T₂ to T? Provide total thermal resistance answer in units of K/W and to 4-decimal places