A horizontal venturimeter with inlet and throat diameters 30 cm and 15 cm respectively is used to measure the flow of water. The reading of differential manometer connected to the inlet and the throat is 20 cm of Hg. Determine the rate of flow. Take C, = 0.98

A horizontal venturimeter with inlet and throat diameters 30 cm and 15 cm respectively is used to measure the flow of water. The reading of differential manometer connected to the inlet and the throat is 20 cm of Hg. Determine the rate of flow. Take C, = 0.98

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Freshwater and seawater flowing in parallel horizontal pipelines are connected to each other by a double U-tube manometer, as shown. Determine the pressure difference between the two pipelines. Take the density of seawater at that location to be ? = 1035 kg/m3. Can the air column be ignored in the analysis?
Blood flow from the left ventricle into the aorta can be modcled as a reducing nozzle. Model both the left ventricle and the aorta as a horizontal tube with diameter of 3.1 and 27 cm, respectively. The pressure in the left ventricle is 130 mmHg and the pressure in the norta is 123 mmHg. Calculate the flow rate of the blood. (Poiood = 1060 kgm-) %3D
PROBLEM 3: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa.
A 400cm long pipe with a smaller diameter of 3.937 inchesand a larger diameter of 11.81 inches as shown below, isinclined at a 30° angle with the horizontal. Calculate the pressure differencein KN/m²between the smaller and bigger diameter parts of the pipe if the velocity of water at the smaller diameter section is 6.56 ft/s. Pi. V₁.d₁. A1 41-0 P2. Vz, dz. Az 32 Datum
A two storey building has two faucets, one in the basement and one in the firstfloor. The maximum water (ρ = 1000 kg/m3) velocity at the basement faucet, when the first floor faucet is closed, is 13 m/s. The faucet diameter is 1.5 cm.Neglect all losses. What would be a maximum height (from the basement floor) for a faucet,to still get a maximum exit velocity of 6 m/s?
Water at 15 degrees Celsius is flowing through a 2-in ID smooth pipe. The friction loss for a 100-ft section of the pipe amounts to 4.8 lbf/lbm. Determine the velocity of the flow.
A hydraulic turbine receives water from a reservoir of 50 meter above it. What is the minimum flow rate in kilograms per second to produce a steady turbine output of 30 MW
There is a storage tank with a height of 5 m. Initially the tank is empty. The cross- sectional area of the tank is 1m?. There is a hole in the storage tank at a level of 2m from the bottom of the tank. The relationship between the volumetric flowrate through the hole and the level of the tank is q=vh. In addition there are two valves at the top and bottom of the tank for inlet and outlet streams. Suddenly, the two valves at the top and bottom of the tank are opened where inlet and outlet stream volumetric flowrates became 1m/s and 0.2m2/s. a)Determine the time for the liquid level to reach 2m
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: A) Neglecting friction, the volume flow rate of airB) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
If the pressure head, velocity head and the potential head at a point in a fluid flow inside a pipeline are 2.1 m 1.9 m and the 4 m respectively, the Total head at that point is Om 6.1 m 8 m 4 m
The pump is used to transfer fluid from one location to another of different height. At inlet and outlet atmospheric conditions are present. The pipe diameter increases after the pump outlet. Determine all the surviving terms of energy equation after simplification. FUM kinetic energy, potential energy, pipe losses none pipe losses, potential energy, pressure increase pressure increase, pipe losses, potential energy kinetic energy, pressure increase, pipe losses OOO