Answered: A hollow steel tube with an inside…

A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 kN. Determine the outside diameter of the tube if the stress is limited to 120 MPa.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 5CQ

See similar textbooks

Related questions

Q: Determine the outside diameter of hallow steel tube that will carry a tensile load of 500kN at a…

A: The stress is load per unit area. The area is surface which is exposed to load. The units of stress…

Q: A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjected to a…

A: Schematic diagram of the given problem:

Q: Determine the normal stress and change in length of the aluminum rod if the temperature was raised…

A: Given data: Aluminium:AA=2000 mm2E=75 Gpaα=23*10-6/°CSteel:AA=855 mm2E=190 Gpaα=17.3*10-6/°C It…

Q: Problem 2: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a…

A: Given data:- Diameter of machine steel cantilever is 1 in Length of steel cantilever is 10 in Forces…

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

A hollow steel tube with an inside diameter of 100 mm
must carry a tensile load of 400 kN. Determine the outside diameter
of the tube if the stress is limited to 120 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
A symmetrical framework consisting of three pin-connected bars is loaded by a forceP (see figure). The angle between the inclined bars and the horizontal is a = 52°. Theaxial strain in the middle bar is measured as 0.036.Determine the tensile stress in the outer bars if they are constructed of a copper alloyhaving the following stress-strain relationship:
2. A long steel pipe is subjected to a state of plane strain (ɛzz = Ezx = Ezy = 0) when the design loads are applied. At the critical point in the pipe, the non-zero stress 143.28 MPa , components are found to be oxx = 53.28 MPa , ơyy Oxy 40 MPa and o22 = 57 MPa . The material has a yield stress of = 245 MPa . Determine the factor of safety in the design based on the von Oy Mises criteria.
3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take maximum tensile stress for cast iron as 14 MPa. [Ans. 6.25 mm]
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 220 mm, a wall thickness of 15 mm, and a length of 4.0 m. The pipe supports a compressive load of 650 kN. After the temperature of the pipe drops 41°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i mm AD = i mm
please just solve the second part
An 8-mm thick steel tank has an outside diameter of 600 mm. It is internal pressure of 2.40 MPa. Determine the maximum subjected to stress in the tank. an
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 5.4 m. The pipe supports a compressive load of 600 kN. After the temperature of the pipe drops 40°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer:
3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the temperature is 20°C, there is no stress in the bar. Compute the stress developed in the beam if the temperature rises to 45°C. Assume that the proportional limit is 235 MPa. a = 11.7 x 10-6 1/C° E = 207 GPa
Determine (d) variable stress and (e) design factor
A pressure-vessel is fabricated by gluing the circular plate to the end of the vessel as shown in figure below. If the vessel sustains an internal pressure of 0.45 MPa, determine the average shear stress in the glue and the state of stress in the wall of the vessel. 20 mm -450 mm - :10 mm