A hollow steel shaft shown in Figure. Find the lengths of the two portions if the angle of twist produced in the two portions of the shaft are equal and the shear stress is not to exceed 60 MPa. (hint: use max torque) * "I 800 mm

A hollow steel shaft shown in Figure. Find the lengths of the two portions if the angle of twist produced in the two portions of the shaft are equal and the shear stress is not to exceed 60 MPa. (hint: use max torque) * "I 800 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
1
What is the absolute maximum shearing stress on the shaft (in MPa) What is the angle of twist of Gear B relative to Gear A (in degrees)? Using the torque applied at Gear B, what will be the power (in kW) generated if it is turning at 50 Hz? indicate the free body diagram
1- The shaft shown in the below Fig. consists of a 75-mm diameter aluminum segment rigidly joined to a 50-mm diameter steel segment. The ends of the shaft are attached to rigid supports. Calculate the maximum shear stress developed in each segment when the torque T = 1130 N.m. is applied. Use G = 28 GPa for aluminum and G = 83 GPa for steel. %3D %3D Aluminum Steel 75 mm diameter 50 mm diameter 1130 N.m Tal 1st 2 m 1 m
2) A hollow tube constructed of metal is subjected to five torques acting in the directions shown in the figure. The tube has an outside diameter of 1.0 in. The allowable shear stress is 12,000 psi. The shear modulus is 9500 ksi. The length between AB, BC, CD and DE is 2ft. a) Draw the internal torque diagram for the shaft using the rules we discussed in class. Based on the allowable shear stress, design the inner diameter of the shaft in inches. b) c) Using your answer from part (b), calculate the total rotation between points A and C in radians. Be sure to track which direction each portion of the shaft is rotating. T₁= TB = T, = Tc= 1000 lb-in. 500 lb-in. 800 lb-in. 500 lb-in. A B D d₂ = 1.0 in. T₂= 800 lb-in. E
For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel and the total angle of Twist. Use G aluminum =28 GPa. G steel =83 GPa.
2. Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque ofT 171N.m the missing Torque 171(T).
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1 = 28 k-in, T2 = -8 k-in and T3 = 10 k-in. (a) What is the angle of twist of the right end due to the applied torque? (b) Plot the angle of twist diagram along the shaft. Let, G= 12×106 psi.
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
A solid circular shaft of diameter 60mm is subjected to an axial stress of 20 MPa. It is further subjected to a torque of 7 KN-m. Find maximum principal stress experienced on the shaft ?