Missing value MT = M0 (kN.m) 170 Kindly write legibly. Thank you Solve for: a) Determine the shear stress in semi-circle portion of the profile b) Compute the maximum torque that can be applied if the allowable shear stress is 200 MPa

Q: A compound shaft is made by mounting a brass sleeve on a steel shaft (which is considered as…

A:

Q: Find the Shear Moment Diagram of the following problems using

A:

Q: The bearings at A and B exert only x and z components of force on the steel shaft. a) Draw shear,…

A: a.

Q: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2 = 1.0…

A: Solution;   Note: The stress concentration factor kt values are taken from the stress concentration…

Q: Two steel springs arranged in series support a load p the upper spring has 12 turns of 25 mm…

A: Given data: n1=12 turnsd1=25 mmR1=100 mmn2=10 turnsd2=20 mmR2=75 mmτmax=200 MPaG=83 GPa Need to…

Q: A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34 in.…

A:

Q: A 40-mm diameter hole is drilled 3-m deep into the steel shaft. When the first torque is removed at…

A: Let shear modulus (G) of steel shaft be 83 GPa. The torque in AB and BC portion is -TAB=6000-2000 =…

Q: Compute the torsional shear stress in a circular shaft with a diameter of 50 mm that is subjected to…

A: GivenT=800 Nmd=50mm=0.05 mFormulaσT=16Tπd3

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: The bearing pad consists of a 150 mm by 150 mm block of aluminum that supports a compressive load of…

A: Given:A=150 mm x 150 mmP=6 KNθ=30°

Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…

A:

Q: The figure below show a stepped shaft in torsion. Compute the maximum shear stress at the step when…

A:

Q: Please answer the below  The required formulas are attached

A: Step 1: Given Gs​=75MPa.Gb​=40MPa.db​=90mmNow let the length of the lever at B is 'l' so, the torque…

Q: Circular solid ACB shaft is fixed supported between the wall at A and B. If the allowable shear…

A: Allowable shear stress τallowable=42 MPa=42×106 N/m2Let the maximum torque applied at section C be…

Q: flange bolt coupling consists of 12-14mm diameter steel bolts on a bolt circle 320mm in diameter and…

A: The diameter of bigger circle is The diameter of smaller circle is The number of bolts on bigger…

Q: In the figure shown below, set F1 710 lb, F2 = 120 lb, F3 = 320 lb, the shaft diameter to 0.5 in,…

A: Given: The force along the x-axis, F1 = 710 lb The force along the y-axis, F2 = 120 lb The force…

Q: A steel shaft ABCD of length L = 6.5 is shown in Figure 4. Given the torque at A, B, C and D is 80…

A:

Q: 2. The hollow shaft used in the system has the following conditions: B Outer Ø: 110 mm Ø Allowable…

A: Shear stress-induced in the shaft at any location (r) from the center is given by,= = 11/12Where, r…

Q: For the steel shaft shown in Fig. Determine the torque transmitted by transverse cross sections at…

A:

Q: as given below 80 mm a) Normal and shear stresses occurring at point A Find and show it on the plane…

A: Given: The diameter of the shaft, d = 20 mm = 0.02 m

Q: Compute the torsional shear stress (MPa) in a 45-in circular steel shaft with a diameter of 42-mm…

A: The length of the circular shaft, (L)=45 in.The diameter of the shaft, (D)=42 mm.The torque on the…

Q: Find the required diameter d0 for a solid circle shaft. b) Find the required outer diameter d2 for a…

A: Given: T =1200 NM G=78 GPa Allowable shear stress =40 MPa Allowable rate of twist 0.78/m TO…

Q: A hollow circular section shaft 2.5 m long is firmly supported at each end and has an inside…

A:

Q: The diameters of the solid shafts in the gear wheel set shown in the figure are dAB = 20mm, dCD =…

A: maximum shear stress = =90 MPa For angular rotation, modulus rigidity a length as assumed (not…

Q: S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute…

A: The answer is given in the below

Q: Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above…

A: Solution:

Q: Determine the maximum shear stress and maximum normal stress of the cantilever shafts in the figures…

A: Length of the shaft→L=200 mm=0.20 m Diameter of the shaft→D=20 mm=0.02 m Transverse force→P=10…

Q: Fx A 75 mm 50 mm 150 mm 350 mm В F2 250 mm y

A:

Q: Q2: For the shaft shown in Figure 2, find the maximum shearing stress in the Aluminum and the steel…

A:

Q: A shaft supported at the ends carries a spur gear and is to transmit 10 kW at 200 rpm. The weight of…

A: Consider a shaft of diameter d and length L is subjected to a torque T. Then, torsional shear stress…

Q: Find the torsional shear stress on a 2 inch diameter shaft if it is subjected to a torque of 561…

A: Given diameter of shaft = 2 inch. Torque=561in-lb.

Q: A flanged bolt coupling consist of six 10 mm diameter steel bolts on a bolt circle 300 mm. in…

A:

Q: In an industrial machine, two shafts have to be connected by using a muff coupling. The shaft…

A: Given,

Q: Compute the torsional shear stress in a circular shaft with a diame to a torque of 800 N-m.

A:

Q: The circular shaft AB consists of a 19.5 mm diameter solid steel cylinder in which a 5.3 mm diameter…

A:

Q: 1. As a section cut in a prismatic bar varies from 0 = 0° to 180° at what values of 0 will the…

A: To find:

Q: The common equation used to calculate the transverse shear stress in a member is: Terans" Starting…

A: Show that,

Q: Determine the normal force at point C(Nc) Express your answer in pounds to three significant…

A:

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.