Solve it fast please its urgent A hollow circuit shaft of inner radius 15mm outer radius 30mm and length 1 m is to be used as a torsionalspring. If the shear modulus of the material of the shaft is 160 GPa, find the torsional stiffness of the shaft ?

Given data, A hollow circular shaft of, inner radius,r1=15 mm, Outer radius, r2=30 mm length,l= 1…

Answered: , find the torsional stiffness of the…

Engineering

Civil Engineering

, find the torsional stiffness of the shaft ?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Related questions

Q: 20-13 A six-lane concrete roadway is being designed for a metropolitan area. This roadway vill be…

A: As per the policy, only the first question in case of multiple questions will be solved. Please…

Q: A reinforced concrete column 200mm in diameter was designed to accommodate an axial load of 350 kN.…

A: Given: The diameter of column is 200 mm. The axial load is 350 kN. The allowable stress of concrete…

Q: Design the torsional and shear reinforcement for the beam as shown in the figure. The resulting L…

A: Concrete shear reinforcement is designed to resist forces greater than concrete's shear strength. A…

Q: Q.2 From the following table, develop network diagram, determine the critical path, and Calculate…

Q: THE SIMPLY SUPPORTED BEAM WHICH HAS LENGTH 6 M IS AS SHOWN AS IN FIGURE 1. IT IS LOADED WITH A…

A: A loaded beam is given and it has ask to check determinacy, to determine support reactions and to…

Q: tvethe Follot 2.

A: Given: x2ydx=y2xdy. Calculation: x2xdx=y2ydyxdx=ydy

Q: SITUATION#1: Given the truss figure below, detemine each member forces using method of joints. 40 AN…

Q: 2- Three - hinged semi-circular arch of uniform cross-section has span of 30m and a rise of 15m, it…

A: Three-hinged arch: Span of the arch = 30 m Crown height = 15 m Concentrated load = 40 kN @ 8 m from…

Q: A reinforced concreté simply supported beam has a span of 5m and carries uniformly distributed dead…

Q: A square foundation in a sand deposit measures 1.22 m x 1.22 m in plan. Given: D = 1.52 m, soil…

Q: A 500-ft curve, grades of g₁ = +2.50% and 9₂ = -3.00%, VPI at station 96 + 80 and elevation 835.26…

Q: Calculate the support reactions at A and B for the loaded beam Assume P = 41 lb, w 86 lb/ft, a= 2.5…

A: Given data : Uniformly varying load (w)=86 lb/ftUpward Point load (P)=41 lba=2.5 ftb=4.5 ft

Q: The cross-sectional dimensions of the beam shown in the figure are a = 4.2 in., b = 5.5 in., d = 4.5…

Q: PROBLEM 1 - Infiltration capacity data obtained in a floating type infiltration test is given below:…

Q: (Given E = 73 Gpa, v = 0.33.) (1) What the normal strains and by using Mohr Circle method: - (ii)…

Q: If the excavated volume is 307.53 m3 and the material is hard clay with a swell percentage of 30 %…

Q: The following data are cross-section notes of the ground which will be excavated for a roadway…

A: Given Data: It is asked to find area of excavation using end-area method.

Q: Select the best hot-rolled W-section for the given column

A: Calculating the factored loadfactored load=1.2Dead Load+1.6Live Load…

Q: Question: Water is flowing in the vertical pipe system shown in the figure. Water exits to the…

A: The given figure is shown below:

Q: A 20 cm diameter and 1200 m long uniform, horizontal new copper pipe installed to carry 140 L/sec of…

A: The Manning's equation is given by: Q=1nAR23S12 Where, A is the area of the cross section. n is…

Q: A circle of diameter d = 200 mm is engraved on a brass plate (see Figure 2). The plate has…

Q: Halp me to out

Q: Clay A precast pile having a diameter of 400 mm is driven through a 4.5 m thick soft clay layer into…

Q: Q.5 How could you answer to address the price adjustment formula which is also known as escalation?…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Determine the effective stress at the bottom of the clay layer.

A: Given data : γSat Sand=18.96 KN/m3γSat Clay=18.50 KN/m3γDry Sand=17.23 KN/m3

Q: Three uniform rods, ABC, DCE and FGH are connected as shown. Which of the following statements are…

A: The connected uniform rods ABC, DCE and FGH rotate about the fixed axis.

Q: the another 6 members

A: As 6 member forces are already provided by the student or some other expert. I am going to find…

Q: A concentrated vertical load of 3000 kN is applied on a horizontal ground surface. Points P and Q…

A: load=3000 kNdepths=1 m & 2 m

Q: DILUTION TECHNIQUE A 20 g/L solution of fluorescent tracer was discharged into a stream at constant…

Q: What is the distance between the kerns for the section given below? K100- 50 200 50 50

Q: Reaction at A. Reaction at B. Reaction C. Directions of reactions A, B, and C.

A: Support reaction: - When external forces are acting on the beam then support of beam will generate…

Q: SITUATION 9: For Items 28-33. 3 k/ft- 2 k/ft D B C - 10 ft10f- –10A 15 ft- El = constant 28. What is…

A: Given data in question UDL UVL Span member length EI is constant To find out Distribution factor…

Q: A storm with I1.5 cm precipitation produced a direct runoff of 5.0 cm The duration of the rainfall…

Q: #2: A beam having an Em. simple span has a cross-section shown in the figure. Defermìne the maximum…

A: Cracked section400xx2-200x-10022= nAxtd-xsolve and substitute the known values x=198.392 mmand also…

Q: Q.1.21 A reservoir discharges through a sluice 0.915 m wide by 1.22 m deep. The top of the opening…

Q: Three samples of loose sand were tested under consolidated undrained (CU) conditions. The failure…

A: Type of conditions = Consolidated Undrained CU Cell Pressure = σ3 = 219 kPa Deviator stress = σ1 -…

Q: A 30 cm diameter concrete pile is driven into a homogeneous consolidated clay deposit (Cy = 40 kPa,…

Question

Solve it fast please its urgent

A hollow circuit shaft of inner radius 15mm outer radius 30mm and length 1 m is to be used as a torsional
spring. If the shear modulus of the material of the shaft is 160 GPa, find the torsional stiffness of the shaft ?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
The failure stress of a homogeneous steel bar having a diameter of 10 mm is 250 MPa. Using a factor of safety of 2.0 and if the elastic mođulus and length of the bar is 200 GPa and 2 m respectively, calculate the elongation in mm of the bar corresponding to the maximum load it can support. (А) 5 (в) 2.5 1.25 D) 0.625
i need the answer quickly
A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long it is subjected to a longitudinal tensile stress of 440 N/mm² and lateral compressive stress is 200 N/mm² in perpendicular directions. E = 2 x 105 N/mm², μ = 0.3. What is the approximate elongation of the bar in the longitudinal direction?
SITUATION 31 A solid mild-steel is rigidly clamped at one end and subjected to an applied torque T = 200 Nm. The shaft is 50 cm in length and has a diameter of 20mm. Calculate the maximum shear stress in the shaft and its angle of twist. Assume the modulus of elasticity be 200 GPa and the modulus of elasticity be 0.22.
The inner and outer diameters of a hollow cylindrical steel are 10mm and 15mm, respectively. It is 1 m long. a) What is the maximum applicable torque such that the shear stress on the shaft does not exceed 100mpa? b) What is the corresponding minimum shear stress value in steel?
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
A steel bar 30 mm in diameter and 2 m long is encased in a shell of cast iron 5 mm thick. Compute the stress in each material, in MPa, if a compressive axial load of 150 kN is applied to the assembly. For steel, E = 200 MPa and for cast iron, E = 100 %3D GPa ( Select the correct response(s): 29.96 MPa 76.39 MPa 212.21 MPa 106.10 MPa 136.32 MPa 152.79 MPa 59.92 MPa 272.84 MPa
An aluminum rod is rigidly attached between a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximun value of P that will not exceed a stress in steel of 169Mpa, in aluminum of 98Mpa and in bronze of 111Mpa.
This is a question from mechanics of material book (axial load chapter). I need the correct solution please, it is very important and answers I have seen are vary.
An aluminium channel section is shown in the figure below: mm 1; mm mm li mm As indicated, the horizontal sides are of length / = 167 mm and thickness 1 - 1 mm while the vertical side is of length l2- 218 mm and thickness 12 - 3 mm. Determine the shear stress in the top side when it is subject to a pure torque of 20 Nm. You may assume that the factor ki may be taken as 0.333. Give your answer in N/mm² to three decimal places.