A heavy-duty helical spring is to be made by wrapping a steel rod 10.6 mm in radius around forming cylinder 141 mm in diameter. If the elongation and shearing stress are limited to 161 mm and 141 MPa, respectively. How many turns are required approximately? G = 83 GPa. Use approximate formula for shear stress

Q: Problem 7 A helical spring is made by wrapping steel wire 12mmp around forming cylinder 100mm in…

A:

Q: Find the length of a flat spiral spring 25 mm wide by 0.5 mm thick to store 8 N.m of energy for a…

A: For a limiting stress of 800 MPa, we need to determine the length of a flat spiral spring 25 mm wide…

Q: Q.2. A helical torsion spring has a wire diameter of 0.038 in, outside diameter= 0.368, 8.5 coils in…

A:

Q: In the figure below, a pulley can pull a 1-ton load from rest to 3 m/s upwards at 2 seconds. AB and…

A: Given: The load, W = 1 ton The speed, v = 3 m/s The time, t = 2 s The compressive stress, σ = 140…

Q: A square end compression helical spring has an operation load range of 3.5KN to 4.2KN.The deflection…

A:

Q: closely coiled helical spring is made of 10 mm diameter steel wire, the mean diameter of  the coil…

A: Given:d=10 mmD=68.4 mmn=8G=100 KN/mm2P=807 N

Q: Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside…

A:

Q: the maximum force, P (in lbs) wit

A:

Q: (a) Draw neat illustrative sketches to bring about the difference between a helical coil tension…

A: helical coil compression spring Springs are the energy storage devices that are used to store…

Q: A helical spring is made by wrapping a steel wire 20 mm diameter around forming a cylinder 150 mm…

A: Given:Diameter of wire, d=20 mmDiameter of spring, D=150 mmElongation, ∆L=100 mmShearing stress,…

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: 1. For the plane truss supported by the spring at node 1, determine the nodal displacements and the…

A:

Q: When a coil spring with a spring rate of 160 lb/in. is compressed 1.6 in., the coils are closed. The…

A:

Q: at is supporting Es will be used -s with shearing ring has a defo

A:

Q: As shown in the figure, a homogeneous 100-kg rigid block is suspended by the three springs whose…

A:

Q: 1. Design a compression helical spring to carry a load of 500 N with a deflection of 25 mm. The…

A:

Q: A coil spring with 5 cm outside diameter is required to work under the load of 190 N. The wire…

A: Outside Diameter (D) = 5 cm = 50 mmWire Diameter (d) = 5 mm Active Coils = 6

Q: A simple torsion-bar spring is shown. The shear stress in the steel [G=11,500 ksi] shaft is not to…

A:

Q: he smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 00mm…

A:

Q: A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8.…

A:

Q: A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter…

A:

Q: The figure illustrates a torsion-bar spring OA having a diameter d = 12 mm. The actuating cantilever…

A: A torsion bar spring OA has a diameter, d=12 mmThe actuating cantilever AB also has a diameter, d=12…

Q: Determine the nodal displacements the forces in each element and the reactions.Use the direct…

A: GivenE1=30×106PsiE2=15×106PsiA=5in2L2=L1=30in

Q: Two concentric plain helical springs of the same length are wound out of the same wire circular in…

A:

Q: a helical compression spring with squared and ground ends is ti be made of a steel wire 79 gpa and…

A: The objective of the question is to determine the spring constant 'k' for a helical compression…

Q: Q6: A thin steel cylinder 1 m long, of 150 mm internal diameter and plate thickness of 5 mm, is…

A: Introduction: A thin cylindrical shell is also known as a pressure vessel, and these vessels are…

Q: An open-coiled helical spring consists of 12 coils, each of mean diameter 60 mm, wire diameter 6 mm…

A: A spring is a mechanical device which is used for the efficient storage and release of energy.…

Q: 2. A helical valve spring is to be designed for an operating load range of approximately 90 to 135…

A:

Q: A helical spring is fabricated by wrapping wire 3/4 in. in diameter around a forming  cylinder 8 in.…

A: Given data :- Wire diameter = 3/4 in  Cylinder diameter = 8 in Shear stress = 18 ksi. G = 12 × 10^6…

Q: A close-coil helical spring is to have a stiffness of 1,000 N/m in compression, with a maximum load…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.