A heat pump cycle delivers energy by heat transfer to a dwelling at a rate of 40,000 Btu/h. The coefficient of performance of the cycle is 3. (a) Determine the power input to the cycle, in hp. (b) Evaluating electricity at $0.085 per kW-h, determine the cost of electricity during the heating season when the heat pump operates for 2000 hours. W cycle= Cost =

A heat pump cycle delivers energy by heat transfer to a dwelling at a rate of 40,000 Btu/h. The coefficient of performance of the cycle is 3. (a) Determine the power input to the cycle, in hp. (b) Evaluating electricity at $0.085 per kW-h, determine the cost of electricity during the heating season when the heat pump operates for 2000 hours. W cycle= Cost =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Preliminary audit taken by an energy manager indicates that the daily energy consumption per hours (with 8 hours / day shift) is distributes as follows: Fuel 1: 500 Kgs, Fuel 2: 900 Kgs, Fuel 3: 820 Kg with calorific value as fuel 1: 30000Kj/kg, Fuel 2: 42000 Kj.Kg, Fuel 3: 50000 kj/Kg. The Cost of the fuel as fuel 1: Rs 30/Kg, Fuel 2: Rs. 90/ Kg, Fuel 3: Rs 50/Kg. The Production Out put is 150000 units. Clearly showing the intermediate computation, answer the following (a) What is the energy Index? (b) what is the cost Index? ( c ) Represent the energy and cost distribution on pi - diagrams and Present your interference based on the above.
1
pls answer completely
A heat pump operating at steady state maintains a dwelling at 23°C on a day when the outside temperature is -2°C. Energy is loss by heat transfer from the dwelling at a rate of 22000 J/s while the heat pump's power input is 5kW. a) Determine the coefficient of performance of the heat pump. b) Determine the power input required if it was a Carnot heat pump.
A gas inside a piston-cylinder assembly undergoes a refrigeration cycle consisting of these three processes: Process 1–2: Compression with pV = constant from p1 = 1 bar, V1 = 1 m3, to p2 = 10 bar, V2 = 0.1 m3. Process 2–3: Constant volume heating until p3 = p1. Process 3–1: Constant-pressure, adiabatic expansion. There are no changes in kinetic or potential energy. a) Find the work for process 1–2 in kJ. b) Find the work for process 2–3 in kJ. c) Find the work for process 3–1 in kJ. d) Find the net work for the entire cycle in kJ. e) Find the net heat transfer for the entire cycle, in kJ. f) Find the heat transfer for process 3–1 in kJ. g) Knowing Q12 = –100 kJ, find the heat transfer for process 2–3 in kJ.
Please answer as soon as possible.
1. Please consider a heat engine that was taking in heat at the rate of 250 Btu/sec and produced 85 hp. Please determine the efficiency of the engine.
Please help
A canister of sevoflurane, an inhaled anesthetic, is warmed to room temperature over the course of 30 minutes. As the gas warms, it pushes on a movable piston with a force of 623 mN, increasing the volume of the gas by 16 cm^3. How much work was done by the gas? A. 0.03 CJ B. 0.27 CJ C. 2.7 CJ D. 270 CJ
Thermal efficiency of a power cycle is 0.8. For the cycle, Wnet = 250 kJ. Determine Qout in kJ. Enter the answer without units and without rounding.
A heat pump is used to maintain the interior of a building at 21 °C. At steady state, the heat pump receives energy by heat transfer from well water at 9°C and discharges energy by heat transfer to the building at a rate of 120000 kJ/h. Over a period of 14 days, an electric meter records that 1490 kW-h of electricity is provided to the heat pump. 1. Draw a schematic diagram(s)
Why would I elect to use grey cast iron rather than a low-carbon steel? Why would I want austenitic rather than ferritic steel? Why is it that polymers are a 100 times stiffer than bulk polymers or a polymer fibers. Why are they so much stiffer and stronger than bulk polymers? What explains that?