Calculate the efficiency of a steam turbine system with the following flow conditions: Steam entering turbine: saturated steam, P2 = 2000 kPa Steam entering the condenser: P3 = 7.5 kPa, Water leaving the condenser: saturated water, P4 = 7.5 kPa Boiler inlet water : P1 = 2000 kPa

Q: Calculate to the correct number of significant figures. (3.14x2.4367) - 2.34

A: The problem is given as, In this, it can be seen that the minimum significant figure of the number…

Q: A tank (contains a fluid of density=1318.4 kg/m3) stands on a frictionless cart (The cart is fixed)…

A:

Q: For the stress element below, when a = 6, b = 4, and c = 6, the principal stress σ1 , the largest…

A:

Q: In a workshop, Drilling operator is working on a Drilling machine. The drilling operator needs to…

A:

Q: Q/ The force in the member (CA) is 12m 50 ку. 10 points 5m 16x

A:

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: During the Brinell harness experiment, it is found that the diameter of indentation diameter is…

A: Answer:

Q: 3 just wearing his suit so you know he's an astronaut, is holding a space space chest along with the…

A: M = 761 g  h = 0.6m          a     distance between E to B         d = 0.7 2+0.62        d =0.92 m

Q: 3

A:

Q: 1. What is the type of robot?

A: ***As per our company policy we are supposed to do only 1 question if you need the rest please…

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: Determine Stres

A:

Q: 15 kN 20 kN 2 m m

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: 1. The tank of the air compressor is subjected to an internal pressure of 8 bar. If the outer…

A:

Q: 1- Draw Torque vs. angle of twist for steel specimen

A: INTRODUCTION : Whenever the specimen subjected to the twisting moment that is torque, the stress…

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: □ 18 F.V.

A: According to the details provided in the question, we need to draw three projection views.

Q: Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown…

A:

Q: 13378.2898 lbm to lbf

A:

Q: The assembly consists of a 3-kg vertical pulley A and a 14 horizontal pulley B. If a 2-kg block is…

A: Given data: m=3 kgM=14 kgr=30 mmR=100 mmh=0.1 m Need to determine the speed of pulley B.

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: So what is the answer? What is y (1)? What is the answer up to two decimal places.

A: y(1) for equation of motion

Q: A piezometer and a pitot tube (close to each other, as described in the figure) are connected to the…

A:

Q: ********** QI/A/ The 4-mm diameter cable BC shown in Figure Q1-4 is made of a steel with E-200 GPa…

A:

Q: Q4. The compound shaft shown in Figure Q4 is attached to rigid supports. For the bronze segment AB,…

A: As per Expert Q&A guidelines we are supposed to answer the first three parts of the given…

Q: 40 7 slug 110 dyne

A: given:

Q: Q3/ For the plate shown in figure below find * (a) ΣΑ YA 7 9. X 8 5

A:

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Moment of Inertia

Inertia can be termed as a resistance offered by a body to change its state. A rigid body initially at rest will apply resistance when acted by an external force that tends to change its state of rest or velocity, or a body initially at motion will provide resistance in changing its state of velocity or motion for coming to a state of rest. In other words, Newton's first law of motion describes the law of inertia of a rigid body.