A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0900 T, it produces a Hall voltage of 0.640 pV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.360 pV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 1.40 mm. Find the density of the charge carriers, each of which has charge of magnitude e). m-3

A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0900 T, it produces a Hall voltage of 0.640 pV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.360 pV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 1.40 mm. Find the density of the charge carriers, each of which has charge of magnitude e). m-3

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Problem 10: A magnetic needle with magnetic moment μ-0.065 Am2 is placed in a uniform magnetic field B0.65 T as shown in the figure. The angle between the direction of the magnetic moment and the direction of the magnetic field is θ 250 Randomized Variables μ= 0.065 Arn B- 0.65T θ 250 Δ Part (a) Express the potential energy U in terms oft, B, θ. | cos(p) sin(p) | cos(α) sin(a) cos(0) sin(0) ( HOMI 4 5 6 BACKSPACE CLEAR Submit Hint I give up! Hints: 1% deduction per hint. Hints remaining: 1 Feedback: 1% deduction per feedback. Part (b) Calculate the numerical value of U in J. Part (c) If θ can be changed, which value has the minimum potential energy? Part (d) If θ can be changed, which value has the maximum potential energy in degrees? Δ Part (e) Ignore the mass of the needle, express the work needed to change the angle from θ to α in terms oftı, B, θ, α Part (f) If α-1500, calculate the numerical value of the work in J.
The Hall effect can be used to determine the density of mobile electrons in a conductor. A thin strip of the material being investigated is immersed in a magnetic field and oriented so that its surface is perpendicular to the field. In a particular measurement, the magnetic field strength was 0.735 T, the strip was 0.101 mm thick, the current along the strip was 2.95 A, and the Hall voltage between the strip's edges was 2.95 mV. Find the density n of mobile electrons in the material. The elementary charge is 1.602 x 10-19 C. 1.56 x104 n 3= -3 Incorrect
A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0880 T, it produces a Hall voltage of 0.740 μV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.360 μV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 2.20 mm. Find the density of the charge carriers, each of which has charge of magnitude e). -3 Need Help? m Read It
A flat copper ribbon 0.330 mm thick carries a steady current of 44.0 A and is located in a uniform 1.80 T magnetic field directed perpendicular to the plane of the ribbon. If a Hall voltage of 9.60 μV is measured across the ribbon, what is the charge density of the free electrons? m-³ What effective number of free electrons per atom does this result indicate?
An electrically conductive rod is moving through a uniform magnetic flux at a constant velocity at right angles, as shown by its cross-section in the diagram. The velocity is in the x-direction, the rod is of length 150 mm along z, and the magnetic flux density is 0.2 T in the positive y-direction. Speed If the potential difference (voltage) across the ends of the rod is 5.8 Volts, what is the magnitude of the velocity? m/s Not perpendicular If the rod is passing through the flux with its axis not at right angles what can you be sure of? The speed to generate 5.8 V would have to be smaller. • The speed to generate 5.8 V would have to be bigger. The speed to generate 5.8 V would be the same.
A cube of edge length = 4.60 cm is positioned as shown in the figure below. A uniform magnetic field given by B = (6.5 î+ 4.0 ĵ + 3.0 k) T exists throughout the region. B # i (a) Calculate the magnetic flux through the shaded face. mWb (b) What is the total flux through the six faces? mWb
A strip of copper is placed in a uniform magnetic field of magnitude 3.5 T. The Hall electric field is measured to be 2.0 x 10-3 V/m. (a) What is the drift speed of the conduction electrons m/s)? m/s (b) Assuming that n = 8.0 x 1028 electrons per cubic meter and that the cross-sectional area of the strip is 4.4 x 10-6 m², calculate the current in the strip (in A). (in m³/C)? nq (c) What is the Hall coefficient m3/c
A uniform magnetic field of 4.95 T points in some direction. Consider the magnetic flux through a large triangular wire loop that has three equal sides of 1.95 m. Determine the maximum of the absolute value of the Determine the minimum of the absolute value of the magnetic flux. 18.8 Wb magnetic flux. 4.18 Wb 9.41 Wb 8.15 Wb 8.15 Wb 0.0 Wb 18.8 Wb 9.41 Wb
In the figure, an electron with an initial kinetic energy of 3.80 keV enters region 1 at time t = 0. That region contains a uniform magnetic field directed into the page, with magnitude 0.00620 T. The electron goes through a half-circle and then exits region 1, headed toward region 2 across a gap of 22.0 cm. There is an electric potential difference AV = 2000 V across the gap, with a polarity such that the electron's speed increases uniformly as it traverses the gap. Region 2 contains a uniform magnetic field directed out of the page, with magnitude 0.0157 T. The electron goes through a half-circle and then leaves region 2. At what time t does it leave? B₁ Region 1 Number i Units Region 2 OB₂
A length of copper wire carries a current of 11 A, uniformly distributed through its cross section. Calculate the energy density of (a) the magnetic field and (b) the electric field at the surface of the wire. The wire diameter is 2.3 mm, and its resistance per unit length is 4.5 2/km. (a) Number 1.456 Units J/m^3 (b) Number 0.0000000000000175 Units J/m^3
In the figure, an electron with an initial kinetic energy of 4.40 keV enters region 1 at time t = O. That region contains a uniform magnetic field directed into the page, with magnitude 0.00640 T. The electron goes through a half-circle and then exits region 1, headed toward region 2 across a gap of 25.0 cm. There is an electric potential difference AV = 2000 V across the gap, with a polarity such that the electron's speed increases uniformly as it traverses the gap. Region 2 contains a uniform magnetic field directed out of the page, with magnitude 0.0220 T. The electron goes through a half-circle and then leaves region 2. At what time t does it leave? Number i B₁ Region 1 Region 2 Units OB₂
Niobium metal becomes a superconductor when cooled below 9 K. Its superconductivity is destroyed when the surface magnetic field exceeds 0.100 T. In the absence of any external magnetic field, determine the maximum current a 1.19-mm-diameter niobium wire can carry and remain superconducting.