A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0800 T, it produces a Hall voltage of 0.700 µV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.300 µV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 2.20 mm. Find the density of the charge carriers, each of which has charge of magnitude e).

A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0800 T, it produces a Hall voltage of 0.700 µV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.300 µV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 2.20 mm. Find the density of the charge carriers, each of which has charge of magnitude e).

Similar questions

The Hall effect can be used to determine the density of mobile electrons in a conductor. A thin strip of the material being investigated is immersed in a magnetic field and oriented so that its surface is perpendicular to the field. In a particular measurement, the magnetic field strength was 0.735 T, the strip was 0.101 mm thick, the current along the strip was 2.95 A, and the Hall voltage between the strip's edges was 2.95 mV. Find the density n of mobile electrons in the material. The elementary charge is 1.602 x 10-19 C. 1.56 x104 n 3= -3 Incorrect
A current of 22.0 mA is maintained in a single circular loop of 4.00 m circumference. A magnetic field of 0.650 T is directed parallel to the plane of the loop. (a) Calculate the magnetic moment of the loop. mA m² (b) What is the magnitude of the torque exerted by the magnetic field on the loop? mN. m
A Hall-effect probe operates with a 120 -mA current. When the probe is placed in a uniform magnetic field of magnitude 0.0880 T, it produces a Hall voltage of 0.740 μV. (a) When it is used to measure an unknown magnetic field, the Hall voltage is 0.360 μV. What is the magnitude of the unknown field? mT (b) The thickness of the probe in the direction of B is 2.20 mm. Find the density of the charge carriers, each of which has charge of magnitude e). -3 Need Help? m Read It
A flat copper ribbon 0.330 mm thick carries a steady current of 44.0 A and is located in a uniform 1.80 T magnetic field directed perpendicular to the plane of the ribbon. If a Hall voltage of 9.60 μV is measured across the ribbon, what is the charge density of the free electrons? m-³ What effective number of free electrons per atom does this result indicate?
An engineer tests a new magnetic flux sensor consisting of a two-dimensional square membrane, 6.30 cm on each side. The sensor measures the magnetic flux through the membrane. The engineer places the sensor so that it is parallel to and 3.90 cm above the xy-plane in the field region. The edges of the sensor are aligned to the positive x- and y-axes. The normal vector for the sensor's surface points straight up, parallel to the z-axis. To test the new sensor, the engineer sets up a region of magnetic field. The magnetic vector field is described by B = (0.0240 T-cm³) x²yî + (0.0550 T-cm-2) xyĵ - (0.399 T-cm¯³) xy² k What magnetic flux B does the sensor measure? x 1.74 x10 -6 ФВ Wb Incorrect
A cube of edge length = 4.60 cm is positioned as shown in the figure below. A uniform magnetic field given by B = (6.5 î+ 4.0 ĵ + 3.0 k) T exists throughout the region. B # i (a) Calculate the magnetic flux through the shaded face. mWb (b) What is the total flux through the six faces? mWb
A uniform magnetic field of 4.95 T points in some direction. Consider the magnetic flux through a large triangular wire loop that has three equal sides of 1.95 m. Determine the maximum of the absolute value of the Determine the minimum of the absolute value of the magnetic flux. 18.8 Wb magnetic flux. 4.18 Wb 9.41 Wb 8.15 Wb 8.15 Wb 0.0 Wb 18.8 Wb 9.41 Wb
In a given region of space, the vector magnetic potential is given by A = x5 coszy + z(0.2+ sin zx) mWb/m. The magnetic flux passing through a square loop with 0.25 cm long edges if the loop is in the x-y plane, its center is at the origin, and its edges are parallel to the x- and y- axis?
In the figure, an electron with an initial kinetic energy of 3.80 keV enters region 1 at time t = 0. That region contains a uniform magnetic field directed into the page, with magnitude 0.00620 T. The electron goes through a half-circle and then exits region 1, headed toward region 2 across a gap of 22.0 cm. There is an electric potential difference AV = 2000 V across the gap, with a polarity such that the electron's speed increases uniformly as it traverses the gap. Region 2 contains a uniform magnetic field directed out of the page, with magnitude 0.0157 T. The electron goes through a half-circle and then leaves region 2. At what time t does it leave? B₁ Region 1 Number i Units Region 2 OB₂
A positively-charged ion travelling at 250 m sis fired between two parallel charged plates, M and N. There is also a magnetic field present in the region between the two plates. The direction of the magnetic field is into the page as shown. The ion is travelling perpendicular to both the electric and the magnetic fields. M ✗ ✗ X X (+) ✗ ✗ N The electric field between the plates has a magnitude of 200 V m¹. The magnetic field is adjusted so that the ion passes through undeflected. What is the magnitude of the adjusted magnetic field, and the polarity of the M terminal relative to the N terminal? Magnitude of magnetic field Polarity of M relative to N (teslas) A. 0.8 positive B. 0.8 negative C. 1.25 positive D. 1.25 negative
In an experiment designed to measure the Earth's magnetic field using the Hall effect, a copper bar 0.430 cm thick is positioned along an east-west direction. Assume n = 8.46 × 1028 electrons/m³ and the plane of the bar is rotated to be perpendicular to the direction of B. If a current of 8.00 A in the conductor results in a Hall voltage of 4.70 x 10-12 V, what is the magnitude of the Earth's magnetic field at this location? μT